Rane RAD15 All RAD Specifications are included in the HAL All Specifications - Page 61
HAL1x Multiprocessor Architects, & Engineers Specification, EXP1x Expander Architects &
View all Rane RAD15 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 61 highlights
Specifications HAL1x Multiprocessor Architects & Engineers Specification The digital multiprocessor shall be a 16 in x 16 out configuration having sixteen inputs: eight balanced analog on plug-in barrier strips that can be either mic- or line-level with switchable +48 V phantom power, and four digital remote audio device ports providing up to two digital inputs and two digital outputs per port, as well as eight balanced analog line-level outputs on plugin barrier strips. Provisions shall be provided for eight digital remotes to control source or preset selection, toggle and/or level control, control logic expansion and wall sensors, located up to 300 meters (1,000 feet) away. The digital remote shall connect to and be powered by the rack room multiprocessor using a dedicated homerun over shielded CAT 5e (or better) cable. Low communication data rates shall permit use of punch-down blocks or RJ-45 patch bays for homerun cable routing flexibility as well as relaxed minimum bend radius. In addition there shall be four contact closure logic inputs on a plug-in barrier strip and two separate relay Form C contact outputs. The multiprocessor shall be expandable using a 512 x 512 channel serial expansion bus interface via RJ-45 connectors, which shall connect up to 32 optional, daisy-chained expander units. The remote audio devices shall provide A/D and/or D/A conversion based on AES3 transport to the wall up to 150 meters (500 feet) from the multiprocessor, as well as units for cascading automatic microphone mixing up to 64 channels, ambient sensing mics, small amplifiers, and advanced paging stations. All remote audio devices and digital remotes shall connect via shielded CAT 5e (or better) cable to the multiprocessor. Further, all remote audio devices and digital remote devices shall support portable use and hot-swapping so that devices may be replaced without shutting down the system, and do so without any audio interference, and that all settings for new devices are automatically downloaded from the multiprocessor along with the correct firmware. The unit shall connect to a computer using a standard Ethernet connector. All functions shall be designed, configured and controlled by a software program featuring a graphical user interface that allows managing the global tasks of discovering, connecting to, and applying configurations to the digital multiprocessor. The hardware-software combination shall automatically check and display the status, location, CAT 5e crimp and wiring integrity, and that audio is flowing to and/or from all peripheral devices. The hardware multiprocessor and the software shall each include Ethernet ASCII text over TCP/IP control support for third-party control systems such as AMX, Crestron and Stardraw Control. The processor shall have an internal 100-240 VAC, 50/60 Hz power supply. The digital multiprocessor shall be a Rane HAL1x running Rane Halogen software, and using Rane Remote Audio Devices (RADs), Rane Digital Remotes (DRs) and Rane IR2 Wall Sensors. EXP1x Expander Architects & Engineers Specification The Expander shall add 16 digital audio inputs and 16 digital audio outputs to the digital multiprocessor via provisions for eight remote audio device ports. The remote audio devices shall provide A/D and/or D/A conversion based on AES3 transport to the wall up to 150 meters (500 feet) from the multiprocessor, as well as units for cascading automatic microphone mixing up to 64 channels, ambient sensing mics, small amplifiers, and advanced paging stations. The eight remote audio device ports shall also support digital remotes to control source or preset selection, toggle and/or level control, control logic expansion and wall sensors, located up to 300 meters (1,000 feet) away. All remote audio devices and digital remotes shall connect via shielded CAT 5e (or better) cable to the multiprocessor. Further, all remote audio devices and digital remote devices shall support portable use and hot swapping so that devices may be replaced without shutting down the system, and do so without any audio interference, and that all settings for new devices are automatically downloaded from the multiprocessor along with the correct firmware. The Expander shall connect to the multiprocessor via a standard RJ-45 connector and cable, with the capability to daisy chain a maximum of 32 expanders to the multiprocessor for a total of 512 inputs and 512 outputs. The processor shall have an internal 100-240 VAC, 50/60 Hz power supply. The Expander shall be a Rane EXP1x with Rane Remote Audio Devices (RADs). Data Sheet - 61