Reebok Rel5 English Manual - Page 5

Assembly

Get Reebok Rel5 PDF manuals and user guides View all Reebok Rel5 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

ASSEMBLY Assembly requires two persons. Place all parts of the elliptical crosstrainer in a cleared area and remove the packing materials. Do not dispose of the packing materials until assembly is completed. Assembly requires the included allen wrench and two adjustable wrenches of your own . 1. The Console (43) requires two ÒAAÓ batteries (not included). Alkaline batteries are recommended. To install batteries, look under the Console (43) and locate the battery door. Refer to the inset drawing. Press the tab on the battery door and remove the battery door. Insert two batteries into the Console. Make sure that the negative ends of the batteries (marked ÒÐÓ) are touching the springs in the Console. When the batteries are correctly installed, re-attach the battery door. 1 43 Battery Door Battery Door 2. While another person holds the Upright (6) in the 2 position shown, connect the Upper Wire Harness (27) to the Lower Wire Harness (28). Carefully slide the Upright (6) onto the Frame (1). Be careful to avoid pinching the Wire Harnesses (27 and 28). Tighten a 3/8Ó Button Head Screw (64) with a 3/8Ó Lock Washer (66) into the front of the Upright and the Frame. Next, tighten two 3/8Ó Button Head Screws (64) with 3/8Ó Lock Washers (66) into the sides of the Upright and the Frame. Note: It may be necessary to loosen the front Button Head Screw slightly in order to attach the other two Button Head Screws. Firmly tighten all three Button Head Screws. Tab 6 64 66 64 Batteries 64 66 27 28 1 3 3. Make sure that there are two 5/16Ó Bushings (29) in the front end of the Right Outer Leg (2). Attach the Right Handlebar (4) to the Right Outer Leg with a 5/16Ó x 1 3/4Ó Hex Bolt (61) and a 5/16Ó Nylon Jam 5 Nut (84). Make sure that the head of the Bolt is on the inside of the Right Handlebar as shown. 3 Attach the Left Handlebar (5) to the Left Outer Leg (3) in the same way. Push the four 2Ó x 3Ó Endcaps (38) onto the Frame (1). 1 38 4 84 61 2 29 4. Make sure that all parts of the elliptical crosstrainer are properly tightened. To protect the floor or carpet from damage, place a mat under the elliptical crosstrainer. 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
5
Assembly requires two persons.
Place all parts of the elliptical crosstrainer in a cleared area and remove the
packing materials. Do not dispose of the packing materials until assembly is completed.
Assembly requires the included allen wrench
and two adjustable wrenches of your own
.
2.
While another person holds the Upright (6) in the
position shown, connect the Upper Wire Harness
(27) to the Lower Wire Harness (28).
Carefully slide the Upright (6) onto the Frame (1).
Be
careful to avoid pinching the Wire Harnesses (27
and 28).
Tighten a 3/8° Button Head Screw (64) with
a 3/8° Lock Washer (66) into the front of the Upright
and the Frame. Next, tighten two 3/8° Button Head
Screws (64) with 3/8° Lock Washers (66) into the
sides of the Upright and the Frame. Note: It may be
necessary to loosen the front Button Head Screw
slightly in order to attach the other two Button Head
Screws.
Firmly tighten all three Button Head
Screws.
2
6
27
28
64
64
64
66
66
1
1.
The Console (43) requires two ±AA° batteries (not
included). Alkaline batteries are recommended.
To install batteries, look under the Console (43) and
locate the battery door. Refer to the inset drawing.
Press the tab on the battery door and remove the
battery door. Insert two batteries into the Console.
Make sure that the negative ends of the batteries
(marked ±—²) are touching the springs in the
Console.
When the batteries are correctly installed,
re-attach the battery door.
1
Batteries
Battery
Door
Battery
Door
Tab
A
SSEMBLY
43
4.
Make sure that all parts of the elliptical crosstrainer are properly tightened.
To protect the floor or carpet
from damage, place a mat under the elliptical crosstrainer.
3.
Make sure that there are two 5/16° Bushings (29) in
the front end of the Right Outer Leg (2). Attach the
Right Handlebar (4) to the Right Outer Leg with a
5/16° x 1 3/4° Hex Bolt (61) and a 5/16° Nylon Jam
Nut (84). Make sure that the head of the Bolt is on
the inside of the Right Handlebar as shown.
Attach the Left Handlebar (5) to the Left Outer Leg
(3) in the same way.
Push the four 2° x 3° Endcaps (38) onto the Frame
(1).
3
4
5
3
1
38
2
84
61
29