Rheem Warrior Gas Series Use and Care Manual - Page 15

Lighting the water heater.

Page 15 highlights

Lighting the water heater. Before operating this water heater, be sure to read and follow the instructions on the label pictured below and all other labels on the water heater, as well as the warnings printed in this manual. Failure to do so can result in unsafe operation of the water heater resulting in property damage, personal injury, or death . Should you have any problems reading or following the instructions in this manual, STOP, and get help from a qualified person. FOR YOUR SAFETY READ BEFORE OPERATING WARNING: If you do not follow these instructions and the Use & Manual instructions exactly, a re or explosion may result causing property damage, personal injury or loss of life. A. This appliance has a pilot which is lit by a piezo- instructions. electric spark gas ignition system. Do NOT open the inner door of this appliance and try to light If you cannot reach your gas supplier, call the fire department. the pilot by hand! C. Use only your hand to turn the gas control knob. B. BEFORE LIGHTING smell all around the appli- Never use tools. If the knob will not turn by hand, ance area for gas. Be sure to smell next to the don't try to repair it, call a qualified service oor because some gas is heavier than air and technician. Force or attempted repair may result will settle on the oor. in a re or explosion. WHAT TO DO IF YOU SMELL GAS Do not try to light any appliance. D. Do not use this appliance if any part has been Do not touch any electric switch; do not use under water. Immediately call a quali ed in- any phone in your building. staller or service agency to replace a ooded Immediately call your gas supplier from a water heater. Do not attempt to repair the unit! neighbor's phone. Follow the gas supplier's It must be replaced! LIGHTING INSTRUCTION 1. STOP! Read safety information above on 8. Depress and hold the gas control knob all the way this label. down. Immediately depress the piezo-electric 2. Set the thermostat dial to the lowest spark generator button several times until the setting by turning the thermostat pilot is lit. The pilot ame can only be seen through dial clockwise until it stops. GAS DO NOT FORCE. CONTROL KNOB 3. Slightly depress the gas control knob PIEZO- the sight glass window located on the inner door. ELECTRIC SPARK 9. Continue to hold down the gas control knob for GENERATOR about one (1) minute after the pilot is lit. If it goes and turn clockwise to "OFF" out repeat steps 3 to 9. position. Note: Knob cannot be turned If the gas control knob does not pop up when from "PILOT" position unless pushed released, stop and immediately call your service down slightly. Do not use force. technician or gas supplier. 4. Wait ve (5) minutes to clear out any CAUTION: RISK OF SCALDING INCREASES WITH HOTTER WATER If the pilot will not stay lit after several tries, turn the gas. If you smell any gas, STOP! follow gas control knob clockwise to "OFF" and call "B" in the safety information above on this label. If you do not smell gas, go to the next step. 5. Remove the outer door from the water heater. Do not attempt to remove the inner door. THERMOSTAT DIAL your service technician or gas supplier. 10. Once the pilot ame is established replace the outer door. 11. Turn the gas control knob counter-clockwise to the "ON" position. Warning do not use gas control knob to regulate gas ow to burner. 6. Locate the piezo-electric spark generator which is located on top of the combination gas control. 12. Set the thermostat dial to desired setting by turning dial counter-clockwise. The preferred starting point for temperature setting is to align the thermostat 7. Turn the gas control knob counter- clockwise to the "PILOT" position. PILOT ASSEMBLY dial pointer ( ) with the "HOT" mark ( ▲ ) on the front face of the control. TO TURN GAS OFF TO THE APPLIANCE 1. Set the thermostat dial to the lowest setting by turning the thermostat dial clockwise until it stops. DO NOT FORCE. 2. Slightly depress the gas control knob and turn clockwise to "OFF POSITION". Note: Knob cannot be turned from "PILOT" position unless pushed down slightly. Do not use force. 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28

15
Lighting the water heater.
Before operating this water heater, be sure to read and follow the instructions on the label pictured
below and all other labels on the water heater, as well as the warnings printed in this manual. Failure to
do so can result in unsafe operation of the water heater resulting in property damage, personal injury,
or death . Should you have any problems reading or following the instructions in this manual, STOP,
and get help from a qualified person.
FOR YOUR SAFETY READ BEFORE OPERATING
This appliance has a pilot which is lit by a piezo-
electric spark gas ignition system.
Do
NOT
open
the inner door of this appliance and try to light
the pilot by hand!
If you cannot reach your gas supplier, call
the fire department.
Use only your hand to turn the gas control knob.
Never use tools. If the knob will not turn by hand,
don't try to repair it, call a qualified service
technician. Force or attempted repair may result
in
Do not use this appliance if any part has been
under water. Immediately call a qualified in-
staller or service agency to replace a flooded
water heater. Do not attempt to repair the unit!
It must be replaced!
LIGHTING INSTRUCTION
TO TURN GAS OFF TO THE APPLIANCE
A.
a fire or explosion.
C.
D.
10.
11.
instructions.
B.
Do not try to light any appliance.
Do not touch any electric switch;
do not use
any phone in your building.
Immediately call your gas supplier from a
neighbor's phone. Follow the gas supplier's
BEFORE LIGHTING smell all around the appli-
ance area for gas. Be sure to smell next to the
floor because some gas is heavier than air and
will
settle on the floor.
WHAT TO DO IF YOU SMELL GAS
Depress and hold the gas control knob all the way
down. Immediately depress the piezo-electric
spark generator button several times until the
pilot is lit. The pilot flame can only be seen through
the sight glass window located on the inner door.
Continue to hold down the gas control knob for
about one (1) minute after the pilot is lit. If it goes
out repeat steps 3 to 9.
If the gas control knob does not pop up when
released, stop and immediately call your service
technician or gas supplier.
If the pilot will not stay lit after several tries, turn the
gas control knob clockwise
to “OFF” and call
your service technician or gas supplier.
Once the pilot flame is established replace the outer
door.
Turn the gas control knob counter-clockwise
to
the “ON” position.
Warning do not use gas control
knob to regulate gas flow to burner.
12.
Set the thermostat dial to desired setting by turning
dial counter-clockwise. The preferred starting point
for temperature setting is to align the thermostat
dial pointer (
) with the “HOT” mark (
) on
the front face of the control.
WARNING:
If you do not follow these instructions and the Use & Manual instructions
exactly, a fire or explosion may result causing property damage, personal injury or
loss of life.
1.
2.
Set the thermostat dial to the lowest setting
by turning the thermostat dial clockwise
until it stops. DO NOT FORCE.
Slightly depress the gas control knob and turn
clockwise
to “OFF POSITION”.
Note: Knob cannot
be turned from ”PILOT” position unless pushed down
slightly. Do not use force.
5.
7.
Remove the outer door from the water
heater.
Do not attempt to remove the
inner door.
6. Locate the piezo-electric spark genera-
tor which is located on top of the
combination gas control.
Turn the gas control knob counter-
clockwise
to the “PILOT” position.
PILOT
ASSEMBLY
CAUTION:
RISK OF SCALDING
INCREASES WITH
HOTTER WATER
9.
8.
STOP! Read safety information above on
this label.
Set the thermostat dial to the lowest
setting by turning the thermostat
dial clockwise
until it stops.
DO NOT FORCE.
Slightly depress the gas control knob
and turn clockwise
to “OFF”
position. Note:
Knob cannot be turned
from “PILOT” position unless pushed
down slightly.
Do not use force.
1.
4.
3.
2.
THERMOSTAT
DIAL
GAS
CONTROL
KNOB
Wait five (5) minutes to clear out any
gas. If you smell any gas, STOP! follow
“B” in the safety information above on
this label. If you do not smell gas,
go to
the next step.
PIEZO-
ELECTRIC
SPARK
GENERATOR