Ridgid OF45175 Owners Manual - Page 7

Motor Specifications and, Electrical Requirements

Get Ridgid OF45175 PDF manuals and user guides View all Ridgid OF45175 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

Motor Specifications and Electrical Requirements Power Supply and Motor Specifications ! WARNING: To reduce the risk of electrical hazards, fire hazards or damage to the tool, use proper circuit protection. Your tool is wired at the factory for operation using the voltage shown. Connect tool to a power line with the appropriate voltage and a 15-amp branch circuit. Use a 15-amp time delay type fuse or circuit breaker. To reduce the risk of shock or fire, if power cord is worn or cut, or damaged in any way, have it replaced immediately. The A-C motor used on this compressor is a capacitor start, capacitor run nonreversible induction type, having the following specifications. It is wired at the factory for operation on 110V-120V AC, 60 Hz service. Voltage Amperes Hertz (Cycles) Phase RPM 110-120 14 60 Single 3450 General Electrical Connections ! DANGER: To reduce the risk of electrocution: 1. Use only identical replace- ment parts when servicing. Servicing should be performed by a qualified technician. 2. Do not use in rain or where floor is wet. This tool is intended for indoor residential use only. ! WARNING: Do not permit fingers to touch the terminals of plug when installing or removing the plug to or from the outlet. 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
The A-C motor used on this compressor
is a capacitor start, capacitor run non-
reversible induction type, having the fol-
lowing specifications. It is wired at the
factory for operation on 110V-120V AC,
60 Hz service.
Voltage
110-120
Amperes
14
Hertz (Cycles)
60
Phase
Single
RPM
3450
Motor Specifications and
Electrical Requirements
7
Power Supply and Motor Specifications
To reduce the risk of electrical
hazards, fire hazards or dam-
age to the tool, use proper cir-
cuit protection. Your tool is
wired at the factory for opera-
tion using the voltage shown.
Connect tool to a power line
with the appropriate voltage
and a 15-amp branch circuit.
Use a 15-amp time delay type
fuse or circuit breaker. To
reduce the risk of shock or fire,
if power cord is worn or cut, or
damaged in any way, have it
replaced immediately.
!
WARNING:
General Electrical Connections
To reduce the risk of electrocu-
tion:
1. Use only identical replace-
ment parts when servicing.
Servicing should be per-
formed by a qualified techni-
cian.
2. Do not use in rain or where
floor is wet. This tool is
intended for indoor residen-
tial use only.
!
DANGER:
Do not permit fingers to touch
the terminals of plug when
installing or removing the plug
to or from the outlet.
!
WARNING: