Rocketfish RF-RBREC Quick Setup Guide (English) - Page 1
Rocketfish RF-RBREC Manual
View all Rocketfish RF-RBREC manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
RF-RBREC Wireless Amplified Audio Receiver Package contents Wireless receiver Remote control Speaker cable (2) 3 ft (91.5 cm) AC power cable Initial setup 1 Unpack the package contents 2 Enable the remote control battery Remove the tab from the bottom of the remote control. Rocketboost technology can connect all audio devices throughout your home to form a home audio network. Rocketboost products include "senders," which send audio streams, and "receivers," which receive the audio. This lets you listen to music from your sender in other rooms, using your receiver. The RF-RBREC is a Rocketboost wireless receiver that includes a built-in audio amplifier. So once you connect your speakers to the RF-RBREC you can listen to audio from your Rocketboost senders. Rocketboost is expandable. Each Rocketboost receiver can select the audio from any sender in your Rocketboost audio network. You can set up your network to meet your specific needs. The illustration on the right shows an example Rocketboost network. User Guide RF-RBAUX (receiver) Cable spool Quick Setup Guide RF-RBREC (receiver) RF-RBWS02 (receiver) RF-RBAUX (sender) Connecting the speakers to the wireless receiver • Connect the right speaker to the right speaker-out connectors on the wireless receiver. Use a red speaker wire to connect the red (+) speaker-out connector and a black speaker wire to connect the black (-) speaker-out connector. Repeat this step to connect the left speaker. Right (rear) speaker Left (rear) speaker Receiver back AC IN SPEAKER-OUT (4-8 Ohm) R L Connecting the wireless receiver to an AC power outlet • Connect one end of the AC power cord to the AC IN connector on the back of the wireless receiver. Then, plug the other end of the AC power cable into an AC power outlet. The Standby indicator turns on. Cable notch To AC power outlet Establishing communication All Rocketboost devices must be "joined" or wirelessly connected to your Rocketboost hub device so that audio can be sent between them. The following steps describe how to join Rocketboost devices. For additional information, see the Rocketboost network notes on the right. 1 If you are setting up your network for the first time, choose one of your Rocketboost senders to be your hub device by setting the Hub Status switch to Enable. For example, if you want the RF-RBAUX sender/receiver to be the hub, set the Hub Status switch on the sender/receiver to Enable. The sender/receiver power indicator lights green if the sender/receiver Hub Status switch is enabled, or lights blue if the sender/receiver Hub Status switch is disabled. 2 If possible, bring your Rocketboost hub device, and the RF-RBREC wireless receiver which you'd like to join to the hub, into the same room. 3 Press the on the Rocketboost hub device to turn it on. 4 Press the on the RF-RBREC wireless receiver to turn it on. 5 Press and hold the on the Rocketboost hub device for more than three seconds to put it into joining mode. The power indicator starts blinking rapidly and the unit will stay in joining mode for 30 seconds. 6 Press and hold the on the RF-RBREC wireless receiver for more than three seconds to put it into joining mode. • When successfully joined, the power indicator LEDs on both products will stop blinking and stay on. • If joining fails after 30 seconds, the power indicator LEDs will begin flashing at a slower rate. If this occurs, repeat the above steps. • Repeat steps 2-6 for each additional Rocketboost device you are adding to your network. For additional information, see your User Guide. Using your wireless receiver 1 Make sure the volume is turned up on the audio device connected to your Rocketboost sender. 2 Play music from the audio device connected to your Rocketboost sender. 3 Adjust the volume level on the wireless receiver. If you have multiple audio sources in your Rocketboost network, press the Source button on the wireless receiver to hear the next audio source. Press the Source button again to cycle through all available audio sources. Rocketboost network notes: Every Rocketboost network must contain one hub device, which helps devices join the network. The network can have only one hub, which you can enable using the hub switch on the back of all Rocketboost senders and sender/receivers. If this is your first Rocketboost product, you should make this device the hub, if you already have Rocketboost products, you should disable hub mode on this device. Important: Hub devices must always have power for your network to operate. The hub device can be in standby (powersaving) mode, but must stay plugged in. QUICK SETUP GUIDE © 2010 BBY Solutions, Inc., All Rights Reserved. Distributed by Best Buy Purchasing, LLC, 7601 Penn Avenue South, Richfield, MN USA 55423-3645 ENGLISH 10-0176