Rocketfish RF-TVMLPT02 Quick Setup Guide (English) - Page 1

QUICK SETUP GUIDE RF-TVMLPT02 Thank you for choosing the Rocketfish RF-TVMLPT02. The RF-TVMLPT02 TV mount is designed to support a TV weighing up to 80 lbs. (36.37 kg). Package contents A Wall plate (1) B Left TV bracket (1) C Right TV bracket (1) M4 bag A D M4 x 12 mm screws (4) E M4 x 30 mm screws (4) F M4/M5 washers (8) C B G M4/M5 spacers (4) M5 bag H M5 x 12 mm screws (4) I M5 x 30 mm screws (4) M4 bag D E F G M6 bag M4 x 12mm J M6 x 12 mm screws (4) K M6 x 20 mm screws (4) L M6 x 35 mm screws (4) M5 bag H M M6 washers (4) N M6 spacers (4) M5 x 12mm Hex key bag O 3⁄16 in. hex key (1) M6 bag J M4 x 30mm I M5 x 30mm M4/M5 Hex key bag M4/M5 O K L M N Lag bolt bag P Concrete anchors (3) Q Lag bolt washers (3) R 5⁄16 in. x 23⁄4 in. lag bolts (3) M6 x 12mm M6 x 20mm M6 x 35mm M6 Lag bolt bag Tools you will need: • Stud finder • Awl • Pencil • Level • Phillips screw driver • Hammer (Concrete Only) • ½ in. socket wrench • 3/16 in. wood drill bit • Tape measure • 3/8 in. masonry drill bit (Concrete Only) • Power drill M6 P Q R in. x 2 in. 1 Attach the TV brackets Option 1: Attaching to a at mounting surface Attach the left and right TV brackets (B and C) to the back of the TV using: The M4/M5 washers (F) and the M4 x 12 mm screws (D) or the M5 x 12 mm screws (H). Or The M6 washers (M) and the M6 x 12 mm screws (J) or the M6 x 20 mm screws (K). B Option 2: Attaching to a curved or irregular mounting surface Attach the left and right TV brackets (B and C) to the back of the TV using: The M4/M5 spacers (G), M4/M5 washers (F), and the M4 x 30 mm screws (E) or M5 x 30 mm screws (I). Or The M6 spacers (N), M6 washers (M), and the M6 x 35 mm screws (L). Note: Use the M4 washers (F) between the spacers and the bracket with the M4 or M5 screws only. B C B or C F or M DH JK 2 Install the wall plate Option 1: Installing to a wood stud wall Caution: Avoid potential injuries or property damage! DO NOT over-tighten the lag bolts. Note: Any material covering the wall must not exceed 5/8 in. (16 mm). a. Locate the studs. Verify the center of the stud with an awl or thin nail or use an edge-to-edge stud finder. b. Level the wall plate (A) and mark hole locations. c. Drill pilot holes as illustrated. d. Align the wall plate (A) with the pilot holes, then place the lag bolt washers (Q) over the holes. Insert the lag bolts (R) through the washers, then tighten the lag bolt with a socket wrench only until they are pulled firmly against the wall plate. a. < 16 mm (5⁄8 in.) b. A C d. G or N F B or C F or M EI L RQ c. 75mm 3 in.