Ryobi AC05RYFL Operation Manual

A - Screw (vis, tornillo)

B - Primer bulb plate (plaque de poire d’amorçage, placa de bomba de cebado)

C - Primer bulb (poire d’amorçage, bomba de cebado)

WARNING:

To reduce the risk of injury, user must read and understand

the operator’s manual for their string trimmer or power head

and this instruction sheet. Always wear eye protection with

side shields marked to comply with ANSI Z87.1. Ensure

compatibility and fit before using this accessory. Do not use

this accessory if a part is damaged or missing. If you are

not comfortable performing any of the functions described

in these instructions, take your unit to an authorized service

center.

WARNING:

Before installing the new primer bulb and/or fuel lines, shut

off engine, wait for all moving parts to stop, allow engine to

cool, drain any remaining fuel from tank into approved fuel

container, press the primer bulb several times to remove any

remaining fuel, then disconnect spark plug wire and move

it away from spark plug. Failure to follow these instructions

can result in serious personal injury or property damage.

PACKING LIST:

Large Primer Bulb

Small Primer Bulb

Supply Fuel Line with Fuel Filter

Return Fuel Line

Removal/Installation Tool

The following instructions apply only to RYOBI and

HOMELITE 2-cycle products with 25cc, 30cc, and 26cc

engines and RYOBI 4-cycle 30cc engines.

INSTALLING A NEW PRIMER BULB

See Figures 1 - 2.

NOTE:

Before removing the air box cover or replacing any parts,

clean the area to remove dirt or debris that could enter the air

box or carburetor.



Remove the air box cover if needed to gain access to screws.

NOTE:

Refer to the Operator’s Manual for your string trimmer

or power head for instructions on airbox cover removal.



Remove the screws and plate and set aside.



Carefully pull on the primer bulb to remove ONLY the primer

bulb.



Install the new primer bulb that best matches the one you

removed onto the primer base.



Reinstall the plate and screws. Tighten the screws securely.



Reinstall the air box cover.

INSTALLING A NEW RETURN LINE AND FUEL

LINE

See Figures 3 - 5.



Place the unit with the fuel supply and return lines facing

you as shown.

NOTE:

For most models, the line on the bottom of the car-

buretor is the supply fuel line, with the filter attached. The

fuel line coming from the top of the carburetor is the return

fuel line.

To remove the old supply fuel line/filter OR old return fuel line:



Remove the fuel cap.

A - Filter (filtre, filtro)

B - Supply fuel line (flexibles de carburant, conductos de combustible)

C - Removal/installation tool (outil de retrait et d’installation, herramienta de

instalación o desinstalación)



Detach the fuel line where it connects to the carburetor.



Using caution to not damage the fuel tank, cut old fuel lines

as close as possible to the fuel tank. With a blunt instrument,

push the remaining cut fuel line into the fuel tank.



Pull the return line or the supply line/filter out of the tank.

NOTE:

It may be helpful to use a tool such as the removal/

installation tool or needle nose pliers to pull the old supply

fuel line/filter to the outside of the tank.

To install the new supply fuel line/filter:



Thread the removal/installation tool into the fuel line holes at

the top of the tank and out of the fuel cap opening. Hook the

end of the tool into the hole on the tapered end of the new

fuel line. Pull the tool, with the fuel line attached, through

the tank and up through the hole. Do not pull too far.



Trim the fuel line to the proper length. Before trimming, make

sure the filter will rest in the lowest point of the fuel tank. Be

sure to trim off the tapered portion of line with the installation

hole.



Install the fuel line securely onto the bottom (lower) connec-

tion on the carburetor.

To install the new return fuel line:



Thread the removal/installation tool into the fuel line holes

at the top of the tank and out of the fuel cap opening. Hook

the end of the tool into the hole on the tapered end of the

return line. Pull the tool, with the fuel line attached, through

the tank and up through the hole.



Trim the return line to the proper length. The line should ex-

tend 1/2 in. inside the tank. Be sure to trim off the tapered

portion of line with the installation hole.



Install the return line securely onto the top (upper) connection

on the carburetor.



Securely replace fuel cap.



Reattach the spark plug wire.

WARNING:

Check for fuel leaks after completing installation of primer

bulb and/or fuel line. Any part that is leaking fuel is a fire

hazard and must be replaced or reinstalled immediately.

If you find any leaks, correct the problem before using the

product. Failure to do so could result in a fire that could

cause serious personal injury.

TRIMMER/POWER HEAD FUEL LINE KIT

AC05RYFL

Fig. 1

Fig. 2

Fig. 3

Fig. 4

Fig. 5

A - Air box cover (couvercle de filtre à air, tapa de la caja de aire)

B - Air box (filtre à air, caja de aire)

C - Primer bulb (poire d’amorçage, bomba de cebado)

D - Latch (loquet, pestillo)

E - Spark plug wire (fil de la bougie, cable de la bujía)

A

B

C

A - Fuel cap (bouchon de carburant, tapa del tanque)

B - Fuel filter (filtre de carburant, filtro de combustible)

C - Fuel tank (réservoir de carburant, tanque de combustible)

D - Supply fuel line (conduit à essence d’alimentation, conducto de suministro

de combustible)

E - Return fuel line (conduit à essence de retour, conducto de retorno de

combustible)

A

C

C

B

B

A

A - Return fuel line (conduit à essence de retour, conducto de retorno de

combustible)

B - Supply fuel line (conduit à essence d’alimentation, conducto de suministro

de combustible)

A

A

D

B

C

E

C

B

D

E

CUT OLD

FUEL LINES

HERE

COUPER LE CONDUIT À ESSENCE USÉ ICI

CORTE LAS LÍNEAS DE COMBUSTIBLE

USADAS EN ESTE LUGAR

B

OWT INDUSTRIES, INC.

P.O. Box 1427, Anderson, SC 29622, USA

1-866-340-3912

995000665

8-29-18 (REV:01)

B

C

A

NOTE: In the artwork, one model is shown when steps are performed the same

way for all models covered by these instructions. If the steps differ based on

the model, illustrations for each method are shown. Your model may vary. For

questions or assistance, please call 1-866-340-3912.

NOTE : Selon les illustrations de l’autre côté, un seul modèle est illustré lorsque

l’exécution des étapes est identique pour tous les modèles concernés par ces

instructions. Si les étapes diffèrent d’un modèle à l’autre, chaque méthode sera

démontrée par des illustrations. Si vous avez des questions ou besoin d’aide,

veuillez appeler au 1 800 860-4050.

NOTA: La ilustración por otro lado solo se muestra uno de los modelos cuando

los pasos son los mismos en todos los modelos cubiertos por estas instrucciones.

Si los pasos difieren dependiendo del modelo, se mostrarán las ilustraciones

de cada modelo. En caso de querer formular preguntas o si necesita ayuda,

llame al 1-800-860-4050.

Ryobi AC05RYFL Operation Manual

Ryobi AC05RYFL Manual

Ryobi AC05RYFL manual content summary: