Ryobi RY42WB User Manual 2 - Page 1

Ryobi RY42WB Manual

Get Ryobi RY42WB PDF manuals and user guides View all Ryobi RY42WB manuals
Add to My Manuals
Save this manual to your list of manuals

Page 1 highlights

WALUBRRICNANTING: ENGINE STARTING PROCEDURE This Engine Starting Procedure is not a substitute for readin1gGGALAtLShONe operator's manual. To reduce the risk of injury, user must read and understand operator's manual before using this product. LLLUUUBBBRRRIIICCCAAANNNTTT 4 1 2 LUBRICANT LLL11LUU11UUGGBBGGBBGGRAARGGAARRLLAAIILLAAICCILLSSCLLCSSAOOAOOAANNNNNNNNTTTT 1 GALLON GAS 50:1 Ratio = Mix 2.6 oz. 2-cycle lubricant with 1 gallon of fresh gasoline in separate gas container. Shake, Pour into fuel tank. Slowly press the PRIMER BULB 10x or until fuel appears. 1 GALLON L1U1GBGGGRAGALAAICLALSSLAOSONNNT 3 SET choke lever to FULL choke. 1 GALLON GAS 9 4 SET throttle/cruise control lever to full throttle. 5 Pull starter grip and rope handle until engine attempts to start (4X max.) 6 SET choke lever to HALF choke. 57 8 36 2 7 8 TO STOP: 9 Pull starter grip and rope until engine starts (6X max.) NOTE: If the unit has not started, return to step 3. Allow the engine to warm for 10 seconds, SET choke lever to RUN. PRESS and HOLD stop switch until engine stops. TO RESTART A WARM ENGINE: If the engine/unit is already hot: SET choke lever to RUN. Set the throttle/cruise lever to full throttle. Pull starter grip and rope until engine starts (6X max.) 1 1-800-860-4050 CALL www.ryobitools.com NOTICE: Do not use E15 or E85 fuel in this product. It is a violation of federal law and will damage the unit and void your warranty. Only use unleaded gasoline containing up to 10% ethanol. Go to www.ryobitools.com and register your new tool on-line. For any questions about operating or maintaining your product, call the RYOBI Help Line! Your product has been fully tested prior to shipment to ensure your complete satisfaction. Troubleshooting tips are also available in your operator's manual. 991000914 6-8-16 (REV:02)

  • 1
  • 2
1
9
4
5
7
6
8
3
2
NOTICE: Do not use E15 or E85 fuel in
this product. It is a violation of federal law
and will damage the unit and void your
warranty. Only use unleaded gasoline
containing up to 10% ethanol.
ENGINE STARTING PROCEDURE
WARNING:
This Engine Starting Procedure is not a substitute
for reading the operator’s manual. To reduce the
risk of injury, user must read and understand
operator’s manual before using this product.
1
2
3
4
5
6
7
8
9
Pull starter grip and rope until engine starts (6X max.)
NOTE: If the unit has not started, return to step 3.
Set the throttle/cruise lever to full throttle.
Allow the engine to warm for 10 seconds, SET choke lever to
RUN.
PRESS and HOLD stop switch until engine stops.
SET choke lever to RUN.
Pull starter grip and rope until engine starts (6X max.)
SET throttle/cruise control lever to full throttle.
Pull starter grip and rope handle until engine attempts to start
(4X max.)
SET choke lever to HALF choke.
SET choke lever to FULL choke.
50:1 Ratio = Mix 2.6 oz. 2-cycle lubricant with 1 gallon of fresh
gasoline in separate gas container. Shake, Pour into fuel tank.
Slowly press the PRIMER BULB 10x or until fuel appears.
TO STOP:
TO RESTART A WARM ENGINE:
If the engine/unit is already hot:
Go to
www.ryobitools.com
and register your new tool on-line.
For any questions about operating or maintaining your product,
call the RYOBI Help Line! Your product has been fully tested prior
to shipment to ensure your complete satisfaction. Troubleshooting
tips are also available in your operator’s manual.
CALL
1-800-860-4050
www.ryobitools.com
991000914
6-8-16 (REV:02)