Ryobi RY903600 User Manual 6 - Page 1
Ryobi RY903600 Manual
View all Ryobi RY903600 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
RYi1000 QUICK REFRENCE GUIDE WARNING: This Quick Reference Guide is not a substitute for reading the operator's manual. To reduce the risk of injury or death, user must read and understand operator's manual before using this product. All page references refer to the operator's manual. IMPORTANT! WARNING: Do not connect to a building's electrical system unless the generator and transfer switch have been properly installed and the electrical output has been verified by a qualified electrician. The connection must isolate the generator power from utility power and must comply with all applicable laws and electrical codes. 1 Put the on/off switch in the ON ( I ) position (see page 13). ON/OFF SWITCH (ON) STARTING THE UNIT FOR THE FIRST TIME 3 Open the vent on the vented fuel cap (see page 13). 6 Put auto idle in OFF (O) position (see page 14). AUTO IDLE (OFF) OFF ON 2 Add fuel. Fill to 1 in. below the top of the fuel neck. (See page 14). NOTICE: Do not use E15 or E85 fuel in this product. It is a violation of federal law and will damage the unit and void your warranty. Only use unleaded gasoline containing up to 10% ethanol. VENTED FUEL CAP (OPEN) 4 Remove engine maintenance cover (see page 13). 7 Move the choke lever to the start position. (see page 14). CHOKE LEVER (START) 5 Add entire bottle of lubricant provided to the generator (see page 13). 8 Pull the starter grip until the engine runs (see page 14). This is a 4-cycle engine. Do not mix fuel and lubricant together. Mix fuel stabilizer with gasoline according to manufacturer's directions prior to filling the tank. Turn the On/Off switch to OFF (O) before adding lubricant. Set unit on flat surface so engine is level. Remove dipstick, wipe clean, put back in hole (but don't screw in) and check lubricant level. Using a generator indoors CAN KILL YOU IN MINUTES. Generator exhaust contains carbon monoxide. This is a poison you cannot see or smell. NEVER use inside a home or garage, EVEN IF doors and windows are open. Only use OUTSIDE and far away from windows, doors, and vents. 9 Allow engine to run for 15-30 seconds, then move choke to RUN position (see page 14). CHOKE LEVER (RUN) 15-30 S STOPPING THE UNIT 1 Put the on/off switch in the OFF ( O ) position (see page 14). ON/OFF SWITCH (OFF) ON .C 120V :12V 5A OFF SMART THROTTLE INODUITCPAUTOT R OVAELRALROMAD LAOLWAROMIL DOCN/PPRUOSTHECTOORFF OFF ON USING THE GENERATOR 1 Connect devices to be powered by generator by following the steps below (see pages 8-9). • Make sure the generator can supply enough continuous (running) and surge (starting) watts for the items you will power at the same time. See page 9 for how to calculate total amount of power needed. • Start the generator with nothing connected. • Plug in and turn on the first load, preferably the largest load you have. • Permit the generator output to stabilize (engine runs smoothly and attached device operates properly). • Plug in and turn on the next load. • Again, permit the generator to stabilize. • Repeat previous two steps for each additional load. IMPORTANT: Never add more loads than the generator capacity. Take special care to consider surge loads in generator capacity. (See pages 8-9.) STORING THE UNIT 1 When preparing to store the generator, allow the unit to cool completely for 30 minutes, then follow the guidelines listed on page 17. TROUBLESHOOTING PROBLEM Engine will not start. POSSIBLE CAUSE SOLUTION On/Off switch is OFF (O). Turn On/Off switch to ON ( I ). No fuel. Fill fuel tank. Stale gasoline or water in gasoline. Drain entire system and refill with fresh fuel. Lubricant level is low. Engine is equipped with Low Oil Shutoff. If engine lubricant level is low, it must be filled before unit will start. Check engine lubricant level and fill, if necessary. Spark plug faulty, fouled, or improperly Replace spark plug. gapped. Choke lever is in RUN position. Move choke lever to START position. Engine stored without treating or draining Drain fuel and carburetor. Refuel with fresh gasoline, or refueled with bad gasoline. gasoline. Dirty fuel filter. Replace fuel filter or contact a qualifed service center. Engine hard to start. Water in gasoline. Weak spark at spark plug. Drain entire system and refill with fresh fuel. Contact a qualifed service center. Engine lacks power. Air filter element clogged. Check air filter element. Clean or replace as needed. Engine stored without treating or draining Drain fuel and carburetor. Refuel with fresh gasoline, or refueled with bad gasoline. gasoline. AC receptacle does not work. Generator is overloaded. Item plugged in is defective. Turn the generator OFF and remove all loads. Restart the unit. Try a different item. Generator makes a "spark knock" or "pinging" An occasional light "knocking" or "pinging" Switch to a different brand of gasoline, making noise. under heavy load is not a cause for concern. sure that the octane rating is 86 or higher. However, if the knocking or pinging occurs If problem continues, contact a qualifed under normal load at a steady engine speed, service center. the problem may be with the brand of gasoline being used. If problem persists after trying the above solutions, contact customer service or a qualified service center for assistance. NOTICE: As the equipment owner, you are responsible for the performance of the required maintenance listed in the Maintenance section. It is recommended that you retain all receipts covering maintenance on your equipment. Neglecting or failing to perform the required maintenance may increase emissions, decrease fuel efficiency, degrade performance, cause irreversible engine damage and/or void your warranty. Make the most of your purchase! Go to www.ryobitools.com and register your new tool online. For questions about operating or maintaining your product, please call, 1-800-860-4050. 991000071 1-29-15 (REV:03)