Samsung CLP-310N Service Manual
Samsung CLP-310N Manual
 |
View all Samsung CLP-310N manuals
Add to My Manuals
Save this manual to your list of manuals |
Samsung CLP-310N manual content summary:
- Samsung CLP-310N | Service Manual - Page 1
Color Laser Printer CLP-315/XAZ Basic Model : CLP-310N,CLP-315 SERVICE Manual Samsung Color Laser Printer CLP-310N The keynote of Product The smallest / The lowest noise High Quality Muti-path CLBP - Model : CLP-31x series - Speed(Color/Mono) : 4/16 ppm(A4). 4/17ppm(Let) - Printing resolution : - Samsung CLP-310N | Service Manual - Page 2
Only to be serviced by appropriately qualified service engineers. High voltages and lasers inside this product are dangerous. This printer should only be serviced by a suitably trained and qualified service engineer. (2) Use only Samsung replacement parts There are no user serviceable parts inside the - Samsung CLP-310N | Service Manual - Page 3
keep Drum cartridge and Toner Cartridge away from children. The toner powder contained in the Drum cartridge and Toner Cartridge may be harmful and if swallowed you should contact a doctor. 1.2.2 Electric Shock and Fire Safety Precautions Failure to follow the following instructions could cause - Samsung CLP-310N | Service Manual - Page 4
the top cover) open as light is admitted to the OPC area and can damage the OPC Drum. - Take care not to scratch the green surface of OPC Drum Unit. If the green surface of the Drum Cartridge is scratched or touched the print quality will be compromised. Service Manual 1-3 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 5
part. The fuser unit works at a high temperature. Use caution when working on the printer. Wait for the installed near the socket outlet and shall be accessible. - Be sure to fix and plug in the power cable securely after the installation so that no one trips over it. Service Manual 1-4 Samsung - Samsung CLP-310N | Service Manual - Page 6
your personal safety reasons prior to applying power to the unit under test. 2. After removing an electrical assembly equipped replacement ESD from its protective packaging until immediately before installing it. Most replacement ESDs are packaged with all . Service Manual 1-5 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 7
1.2 Caution for safety 1-2 1.3 ESD Precautions 1-5 2. Product spec and feature 3URGXFW6SHFL¿FDWLRQV 2-1 2.1.1 Product Overview 2-25 2.3.4 Network Interface 2-26 2.3.5 Printer Driver Status Monitor 2-26 2.3.6 System F/W Flow 2-27 2.3.7 Alarm Shortage 2-28 2.3.8 Error status 2-28 - Samsung CLP-310N | Service Manual - Page 8
the printer 3-5 3.4 Disassembly Procedure 3-7 3.4.1 Cover 3-7 3.4.2 ITB 3-9 3.4.3 Fuser 3-9 3.4.4 HVPS board 3-10 3.4.5 Main PBA 3-10 3.4.6 SMPS board 3-11 3.4.7 LSU Unit 3-11 3.4.8 Holder Pad 3-12 3.4.9 Transfer Unit 3-12 3.4.10 OPE PBA 3-13 4. Alignment & Troubleshooting 4.1 Alignment - Samsung CLP-310N | Service Manual - Page 9
the Symptoms 4-17 4.2.2 Troubleshooting Checklist 4-18 4.2.3 Solving General Printing Problems 4-19 4.2.4 Solving Print Quality Problems 4-30 4.2.5 Common Windows Problems 4-48 4.2.6 Common Macintosh Problems 4-49 4.2.7 Common Linux Problems 4-50 4.2.8 Major Problems Trouble shooting 4-54 - Samsung CLP-310N | Service Manual - Page 10
Continued 6. System Diagram 6.1 Block Diagram 6-1 6.2 Connection Diagram 6-2 7. Reference Information 7.1 Tool for Troubleshooting 7-1 7.2 Acronyms and Abbreviations 7-2 7.3 Select a location for the printer 7-4 7.4 A4 ISO 19752 Standard Pattern 7-5 - Samsung CLP-310N | Service Manual - Page 11
BaseT network connector 7.Control Panel • No LCD, 1 keys and 6 LEDs 8. Toner cartridge • Black : 1K (initial) / 1.5K (sales) • Color : 0.7K (initial) / 1K (sales) - The initial toner cartridge has not the CRUM. 9. Color • There are two kinds of colors. (Gray and Black) Service Manual 2-1 Samsung - Samsung CLP-310N | Service Manual - Page 12
Emulation Auto Emulation Sensing Font Type Number Power Save Resolution Normal Toner Save FPOT Duplex Print Printable Area RET From Ready From Idle From Cold Boot Print Margin CLP-310/315 384x314x237 mm 11 Kg B&W : 17ppm@Letter 16ppm@A4 Color : 4ppm@A4,.Letter NA SPL-C NA NA NA Yes (5/10 - Samsung CLP-310N | Service Manual - Page 13
-Color Management Support [Mac] -N-up printing 4XDOLW\ %HVW1RUPDO'UDIW &RORUPRGH &RORU*UD\VFDOH >/LQX[@ - N-up printing 4XDOLW\ %HVW1RUPDO'UDIW [Common] 1:,QVWDOO GXULQJGULYHULQVWDOO :+4/ :LQGRZVLQFOXGLQJYLVWD :LQGRZVLQFOXGLQJYLVWD Service Manual 2-3 Samsung - Samsung CLP-310N | Service Manual - Page 14
Product spec and feature Item /DQJXDJH/RFDOOL]DWLRQ Smart Panel 1HWZRUN Management 6PDUW7KUX CLP-310/315 CLP-310N >:LQGRZV@ .RUHDQ(QJOLVK)UHQFK 6:6 /LQX[0DF QRWVXSSRUW6:$6 6:6QHHG, H[SORUHURU+LJKHU 1$0DQDJHPHQW 1$ 6PDUW7KUX Service Manual Samsung Electronics - Samsung CLP-310N | Service Manual - Page 15
spec and feature 2.1.2.3 Interface Item ,QWHUIDFH 1HWZRUN ,QWHUIDFH Parallel 86% 1HWZRUN Wireless Protocol 1HWZRUN26 CLP-310/315 1$ 86% 1$ 1$ 1$ 1$ 8VHU ,QWHUIDFH /&' 238, 6RXQG8, 1$ .H 1$ CLP-310N [+38;6RODULV6XQ26 6&281,; 1$ .H 1$ Service Manual 2-5 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 16
spec 5DWH Cassette 3ULQWLQJ6NHZ 7RS Side CLP-310/315 VKHHWV#J̅ 0D[ (QYHORS 6KHHWV 7UDQVSDUHQF\ PP PP PP &DVVHWWH PP &DVVHWWH CLP-310N VKHHWV#J̅ 0D[ (QYHORS 6KHHWV 7UDQVSDUHQF DVVHWWH PP &DVVHWWH Service Manual Samsung Electronics - Samsung CLP-310N | Service Manual - Page 17
LQGLYLGXDOFRORUVRQHDFKSDJH 8VDJHFRQGLWLRQVDQGSULQWSDWWHUQVPD\FDXVHUHVXOWVWRYDU\ *Image counts based on one color on each page. If you print documents in full color (Cyan, Magenta,Yellow, Black), the life of this item will be reduced by 25%. Service Manual Samsung Electronics - Samsung CLP-310N | Service Manual - Page 18
spec and feature 2.1.2.6 Reliability & Service Item 0D[0RQWKO\'XW\ 6(7/LIH&\FOH 07%) 0775 5HDOWLPH&ORFN 6\VWHPUHFRUG 0LQLPXP6\VWHP5HTXLUHPHQW CLP-310/315 CLP-310N 0%+'',QWHUQHW([SORUHU 0%+'',QWHUQHW([SORUHU Service Manual 2-8 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 19
spec and feature 2.1.2.7 Environment Item 3RZHU Consumption 3RZHU6XSSO\ Noise :DUP8S7LPH 7HPSHUDWXUH +XPLGLW\ $OWLWXGH CLP-310/315 Accessory Item CLP-310/315 CLP-310N Quick setup guide Yes Yes 3RZHU&DEOH ($ ($ 3ULQWHU&DEOH ($ ($ Service Manual 2-9 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 20
Product spec and feature 2.1.3 Model Comparison Table ,PDJH Samsung CLP-310 Samsung CLP-300 HP CLJ 1600 HP LJ 1022 Speed SSP processor 0HPRU\ Print Language ,QSXW 0+] 32 MB SPL-C VKHHWV&67 'XSOH[ ,QWHUIDFH 6L]H PP :HLJKW Noise 7RQHU %ODFN &RORU Manual 86 11 kg G%$ - Samsung CLP-310N | Service Manual - Page 21
Product spec and feature 2.2 System Overview 7KLVFKDSWHUGHVFULEHVWKHIXQFWLRQVDQGRSHUDWLQJSULQFLSOHVRIWKH of System Fuser T2 Roller Regi. Roller Pick up Roller Stacking Area T1 Roller ITB Waste Tank OPC LSU Cassette DEVE Y DEVE M DEVE C DEVE K Service Manual 2-11 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 22
spec 3DSHU6L]H6HQVRU 1RQH ΘLSU(Laser Scan Unit) 7KH/68XQLWLV Error 3RO\JRQ0RWRU(UURU +V\QF(UURU Phenomenon 7KH5RWDWLRQRI3RO\JRQ0RWRUFDQQRWUHDFKVWDEOH 7 KRXJKWKHURWDWLRQRI3RO\JRQ0RWRUUHDFKVWDEOHWKHVLJQDORI+V\QFLV not occurred Service Manual 2-12 Samsung - Samsung CLP-310N | Service Manual - Page 23
Product spec and feature Ι2nd Transfer Ass'y ‡7KHOLIHVSDQ 3ULQWRYHUVKHHWV LQa 6SHFL¿FDWLRQ 6LPLODUWR&/36HULHV DSDSHUSDVVHVEHWZHHQDKHDWUROOHUDQGDSUHVVXUHUROOHUWRQHUDGKHUHVWRWKHVXUIDFH RIDSDSHUSHUPDQHQWO\ Service Manual 2-13 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 24
‡7KH,7%XQLWLQFOXGHVVW7UDQVIHU5ROOHU ΝImaging Unit ‡7KHOLIHVSDQ 3ULQWRYHU24,PDJHV ‡,PDJLQH8QLWincludes OPC(Organic Photo-Conductor) drum ΞToner cartridges ‡7KHOLIHVSDQ & RORU!7(Initial)/1000(Sales) images 6WG,62 983ULQW2XW %ODFN!1000 - Samsung CLP-310N | Service Manual - Page 25
Product spec and feature 2.2.1.2 EP Process - Structure of EP Process 3 ,PDJH RQ23& ,7%8QLW Blade 3 ,PDJH on Media 23& 0HGLD3DWK a 'HYHORSHU /DVHU6FDQQLQJ8QLW Blade Eraser &KDUJHU Service Manual 2-15 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 26
Product spec and feature ΗCharging ‡&RQGXFWLYH5ROOHUFKDUJLQJ ‡$SSOLHGYROWDJH N9 ‡&KDUJHDFFHSWDQFH 9 ‡23&FRDWLQJ 23&DQGWUDQVIHUUHGRQWR,QWHUPHGLDWH7UDQVIHU %HOW KHUHDIWHU,7% WRIRUPDFRORULPDJHRQ,7% Service Manual Samsung Electronics - Samsung CLP-310N | Service Manual - Page 27
Product spec and feature ΚTransfer 1 ‡0XOWLSDVVWUDQVIHU ‡,QGLUHFWWUDQVIHU ‡7UDQVIHUYROWDJH aN9 FRQWUROODEOH ‡5ROOHUGLDPHWHU 3UHVVXUH5ROO &RORU,PDJHRQPHGLDLVPHOWHGGRZQDQG¿[HGLQWRPHGLDE\IXVLQJSURFHVV Service Manual Samsung Electronics - Samsung CLP-310N | Service Manual - Page 28
Product spec and feature 2.2.2 Main PBA Description 2.2.2.1 Main Controller PBA 14 16 9 7 E 4 5 10 C 30 8 D 20 A 17 22 12 &580&RQ 3 /68&RQ 3 30 (PSW\ 3 $ &38 &KRUXV B ''5 0% C 125)/$6+ 0%RU0% ' ((3520 E 3+ - Samsung CLP-310N | Service Manual - Page 29
Product spec and feature 2.2.2.3 Main PBA Description CHORUS 3 $3URSULHWDU\6R&&+2586H[HFXWHVDQGFRQWUROV WRVWRUH6\VWHP3URJUDPVLQFOXGLQJWKH2SHUDWLQJ6\VWHP ƒ7\SH125)ODVK ƒ%XVELWZLGWK ƒ6L]H0% 0%DW1:0RGHO&/31 Service Manual 2-19 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 30
Product spec and feature System Memory 8VHGDVD3ULQWLQJEXIIHUIRUSULQWLQJD6FDQEXIIHUIRUVFDQQLQJD(&0%XIIHUIRU WKHKLJKYROWDJHRXWSXWV ƒ$'& 5HDGLQJWKH)XVHU¶VWHPSHUDWXUHDQGWKHKLJKYROWDJHRXWSXWV¶IHHGEDFN ƒ&RYHU2SHQ6HQVLQJ Service Manual 2-20 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 31
Product spec and feature 2.2.2.4 SMPS(Switching Mode Power Supply) PBA 6036LVWKH &21 93LQ *1'3LQ 9“ a9 P9SS 10.2W 11W 6KXWGRZQRU)XVH Protection Service Manual 2-21 CH2 9 &21 93LQ *1'3LQ 9“ a9 P9SS : : 6KXWGRZQRU2XWSXW - Samsung CLP-310N | Service Manual - Page 32
Product spec and feature 2.2.2.5 HVPS(High Voltage Power Supply) PBA 7KH+936FUHDWHV %HOWDQG5ROOHU 5HJL 0DLQ3%$ %,$6$& 9a %,$6'& 9a &+$5*(5 9a 7 9a Waste 23&:DVWH ,7%7HQVLRQ 1LS([LW 7 9a 9a Service Manual 2-22 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 33
Product spec and feature 1) Charger Voltage : Charger ‡)XQFWLRQ YROWDJHWKDWFKDUJHV23&VXUIDFHXSWR9a9 ‡2XWSXW GHQVLW\ZLOOEHH[WUHPHO\GRZQ LI'HYHLVÀRDWLQJ IRULQVHFXUHWHUPLQDOFRQWDFW GHQVLW\ZLOOEHH[WUHPHO\GRZQ Service Manual 2-23 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 34
Product spec and feature 2.2.3 CRUM 7KH&/31HQJLQHZLOOEHHTXLSSHGZLWKHOHFWURQLFVWKDWFDQUHDGDQGZULWH 1DPH0)&GDWH6HULDO1XPEHU 0DQXIDFWXUH,QIRUPDWLRQ !/HWFDUWULGJHUH¿OOHULQLWLDOL]HPDQXIDFWXUHLQIRUPDWLRQDQGOLIHVSDQLQIRUPDWLRQ Service Manual Samsung Electronics - Samsung CLP-310N | Service Manual - Page 35
Product spec and feature 2.3 S/W Structure and Descriptions 2.3.1 Architecture 7KHEHOW&580LQWHUIDFHERDUGLVDWUDQVPLVVLRQEHOW&580LQWHUIDFH 6WDWXV0RQLWRUKDVQRXVHULQWHUIDFH,WVKRZVRQO\+70/KHOSZKHQDQ\HUURURFFXUVGXULQJSULQWLQJMREV Service Manual 2-25 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 36
WKHXVHUDOWKRXJKWKHHUURUKDVRFFXUUHGZKLOHSULQWLQJ Status Monitor Set last error status *HWRSWLRQYDOXH HQDEOHGLVDEOH or SROOLQJLQWHUYDO 6\VWHP 5HJLVWU\ 6HWRSWLRQYDOXH HQDEOHGLVDEOH or SROOLQJLQWHUYDO *HWODVWHUURUVWDWXV 3ULQWHU'ULYHU Service Manual Samsung Electronics - Samsung CLP-310N | Service Manual - Page 37
$XWR&RORU5HJLVWUDWLRQ pattern printing &RORU5HJLVWUDWLRQ DGMXVWPHQW 3DJH6\QF PRGLI\ /LQH6\QF PRGLI\ 9LGHR&ORFN)UHT PRGLI\ /68temperature control PWM 2XWSXW /(' PWM Comparator /68 36\QF /6\QF clock 9LGHRGDWD 9LGHRVLJQDO generator Service Manual Samsung Electronics - Samsung CLP-310N | Service Manual - Page 38
Product spec and feature 2.3.7 Alarm Shortage 7RQHU &0 - Samsung CLP-310N | Service Manual - Page 39
Product spec and feature 2.3.9 CRUM Overview - Stands for "Customer Replaceable Unit Monitor" - EEPROM, SAMSUNG CRUM is used for CRUM Memory. - CRUM stores various information on consumables (including consumables' life). - In CLP-31x Series, total four CRUM's are used (four on toner cartridges) - Samsung CLP-310N | Service Manual - Page 40
2.3.11 Initailize Flow Product spec and feature Service Manual 2-30 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 41
Product spec and feature Service Manual 2-31 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 42
shock. * Do not disassemble the LSU unit. Once it is disassembled dust is admitted to the mirror chamber and will seriously degrade print quality. There are no serviceable parts inside. * Regularly check the latch away from the part to which it is latched. Service Manual 3-1 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 43
occur. Item Black Toner cartridge Color Toner cartridge Imagine unit Waste Toner Pick-up roller Fuser unit Transfer Unit ITB Pages Printed Approx. Initial : 1,000 Pages* Sales : 1,500 Pages* Approx. Initial : 700 Pages* Sales : 1,000 Pages* Approx. 24000 images** Approx. 10000 images Approx. 50 - Samsung CLP-310N | Service Manual - Page 44
from the skin will contaminate the surface and reduce print quality. * Do not touch transfer roller when cleaning inside of machine. If transfer roller gets dirty, printing quality could be low. * Please refer to the User Manual for cleaning instructions. Service Manual 3-3 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 45
to laser radiation can cause blindness. 2) Disassembly of the ITB unit Do not disassemble the ITB. The alignment of the home sensor is critical and is set up in the factory on a special jig. Incorrect re-assembly will cause print quality degradation. 3) Care of the Toner cartridge Toner cartridges - Samsung CLP-310N | Service Manual - Page 46
and that, when reassembling the printer, the correct screws are M2.6,L6,ZPC(WHT),SWRCH18A,- 7 6001-000485 Toner K SCREW-MACHINE;PH,+,-,M2.6,L4,ZPC(WHT), 000282 Imaging unit SCREW-TAPTITE;BH,+,-,B,M3,L8,ZPC(BLK),SWRCH18A,- 10 6003-000282 Cartridge-Transfer Service Manual 3-5 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 47
GND WIRE 18 Main CRUM-JOINT 19 HVPS EXIT 20 HVPS Sensor(Regi) 21 HVPS Waste Toner Sensor 22 HVPS B'd Sensor (ITB Tension /OPC Waste) PIN 16-(10+5) 26-26 4-4 2-2 16-16 3-3 3-3 10-10 2-2 4-(2+2) JC39-00904A JC39-00906A JC39-00897A JC39-00898A Service Manual 3-6 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 48
procedures. If you ¿nd the certain unit or Ass'y, please consult the name of unit under the picture. 3.4.1 Cover 1. Take out the Cassette. 3. Remove the Toner waste tank. 2. Open the Front cover and take out the CMYK Toner. 4. Remove the Imaging Unit. Service Manual 3-7 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 49
/Right cover and release it. 6. Remove the one screw from the rear of SET. 8. Remove the connector from front cover. And remove the front cover. Service Manual 3-8 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 50
the Right cover. And remove the 2 connector as shown below. 2. Remove the 4 screw, and move the shaft as shown below. And remove the Fuser unit. Caution-The fuser is very hot. So turn the printer off and wait until the printer to cool before replacing it. Service Manual 3-9 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 51
the center. Hook 3.4.5 Main PBA 1. Remove the harness cover after remove the one screw. 2. Remove the all harness and 4 screws. And release the Main PBA. Service Manual 3-10 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 52
all harness and 4 screws. And remove the SMPS board. 3.4.7 LSU Unit 1. To remove the LSU from the bottom of the SET, ¿rst remove the harness cover after remove the 2 screws. And remove the 3 screws. 2. Release the LSU unit after remove the 2 Flat cable. Service Manual 3-11 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 53
3.4.8 Holder Pad 1. Remove the sub PBA. And release the Guide Pick up unit after remove the 4 screws. 2. Release the holder pad after remove the hook of both side. 3.4.9 Transfer Unit 1. Remove the Transfer unit from the rear cover by pressing the hook. Service Manual 3-12 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 54
Guide Pick up unit.( refer to 3.4.8) 1. Remove the hook from the position A and push to the left side. 2. Separate the Pick up roller Assy after release the position B. 3. Remove the hook of the part C,B in sequence. 4. Separate the Pick up rubber. j h i Service Manual 3-13 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 55
for service, such as the product maintenance method, the test output related to maintenance and repair, Jam removing method, and so on. It includes the contents of manual. 4.1.1. Control Panel 4.1.1.1 Overview - The CLP-31x series printers do not have LCD panel which is used in other color model - Samsung CLP-310N | Service Manual - Page 56
of manual feeding function in CLP-310 series will be determined - Firmware downloads mode function Turn on the printer at the same time that the button is pressed. If all LEDs scroll, release the button and download the firmware ROM file via USB port Service Manual 4-2 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 57
& Troubleshooting 4.1.2.2 LED Function There are five LEDs present. Status led indicate the error/online status of the printer in idle mode. In error mode, the status LED glows by red color and in ready mode, it glows by green color. The other four LEDs indicate the toner status. If the black toner - Samsung CLP-310N | Service Manual - Page 58
The machine is printing data. lights red all LEDs off • The machine is experiencing an error, such as jammed paper, open cover, empty paper, installed waste toner container, or full waste toner container. • The machine is experiencing a service required error, such as LSU error, fuser error, or - Samsung CLP-310N | Service Manual - Page 59
clearing paper jams, you must open and close the front cover or rear cover. 1. Pull the tray out of the printer and remove the jammed paper. 2. To remove the jammed paper, open the rear cover. If you can not find the jammed the paper,Go to the next step. Service Manual 4-5 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 60
Alignment & Troubleshooting 3. Carefully remove the paper by pulling in the direction as paper out of the printer. The inner cover will then close automatically. 4. Push the fuser levers upwards. 7. Close the top cover. Make sure that it is securely closed. Service Manual 4-6 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 61
Alignment & Troubleshooting 8. Push the fuser levers downwards. 9. Open and then close the rear cover or front cover to resume printing. Service Manual 4-7 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 62
problems. 4.1.4.1 Printing a Demo Page Print a demo page to make sure that the printer is operating correctly. To print a demo page: In ready mode, press and hold the Stop button for 2 seconds. A demo page showing the printer's features and capabilities is printed. Service Manual 4-8 Samsung - Samsung CLP-310N | Service Manual - Page 63
, last used date, first installed date. 6. Imaging-unit Information : shows image count, last used date, first installed date. 7. Network configuration report : shows network information set up in the printer. (Mac address, NIC F/W version, TCP/IP, IPP etc. ) Service Manual 4-9 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 64
Image by abnormal tranfer Ghost, Damaged Image by abnormal tranfer Background Black Spots or Vertical Black Band Exit roller Pressure roller T2 roller Regi roller T1 roller oŒˆ›G™–““Œ™ ITB OPC OPC Charge roller Supply ro Deve roller Pick up roller Service Manual 4-10 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 65
Enterence When trying to check the CLP-310N EDC Mode, additional EDC execution program needed. [ Procedure of EDC Mode operation ] a) First, turn on the Power of Printer, wait until Ready state b) In item Stop testing or the upper menu 4.1.6.3 EDC Map Service Manual 4-11 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 66
Troubleshooting 3 Y Toner M Toner C Toner K Toner Regi Clutch T2 Clutch ITB Clutch Tray1 Clutch Tray2 Clutch Regi. Sensor Exit Sensor Waste Box Discription waste Box exists , "Installed" message will be displayed. If not, "Not Installed" message will be. Service Manual 4-12 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 67
& Troubleshooting Item Cover Laser Diode Off message will be. When select key is pushed, Eraser On message will be displayed . If not, Eraser Off message will be. When select key is pushed, Fuser On message will be displayed. If not, Fuser Off message will be. Service Manual 4-13 Samsung - Samsung CLP-310N | Service Manual - Page 68
Alignment & Troubleshooting 4.1.6.3(d) HVPS Test Item Charger T1 T2 T2 REVERSE Dev DC Dev AC Vpp Dev AC Charger 122V ~ 2188V Duty : 50% -> "2552V", Range : 264V ~ 4730V Duty : 50% -> "-269V", Range : -1V ~ -591V Duty : 50%-> "1210V" , Range : 800V ~ 2160V Service Manual 4-14 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 69
waste toner box ĶPaper Jam - Paper Jam at the tray1 • Paper is not picked up • Cover Open /Close, When you still want to continue printing - Paper Jam inside printer • There is a paper inside printer • After cover Open , Paper must be removed, and then close the cover Service Manual 4-15 Samsung - Samsung CLP-310N | Service Manual - Page 70
must be checked - Dev. Home error • Home of Development is not checked or checked at the abnormal time • Clutch of Development or Main board must be checked - ADC not Confirm Error • Signal of confirmation for ADC is not detected • Main board must be checked Service Manual 4-16 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 71
of the problem from the customer. Power On LED Panel ON? - No Power - Power Module error - Main PBA Status LED Green OK? Print(test pattern) printing Quality is Nomal? END Indicate "Red Lamp ON" Refer to "4.1.2.2 LED Function" Refer to "Solution of Image Problem" Service Manual 4-17 Samsung - Samsung CLP-310N | Service Manual - Page 72
page is interrupted during printing, go to "Solving General Printing Problems" • See "Solving General Printing Problems" • See "Solving Print Quality Problems" • See "Common Windows Problems" • See "Common Macintosh Problems" • See "Common Linux Problems" Service Manual 4-18 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 73
Select Samsung CLP-31x Series as your default printer. Check the printer for the following: The printer cover is not closed. Paper is jammed. No paper is loaded. A toner cartridge is not installed. Close the printer cover. Clear the paper jam. Load paper. Install the toner cartridge. The printer - Samsung CLP-310N | Service Manual - Page 74
printer driver may be incorrectly installed. Reinstall the printer driver; see the Software Section. Try printing a test page. The printer is malfunctioning. Check the LEDs on the control panel to determine if the printer is indicating a system error. Service Manual 4-20 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 75
. Remove paper from the tray and reload it correctly. Check that the paper guides are set correctly. There is too much paper in the tray. Remove excess paper from the tray. The paper is too thick. Use only paper that meets printer specifications. Service Manual 4-21 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 76
]. See the Software section. Change the port setting to the USB or network port to improve print speed. Your printer prints A4-sized paper at 16 ppm in black and white mode and 4 ppm in color mode. From the Start menu, choose Settings and Printers. Right-click the Samsung CLP-31x series printer icon - Samsung CLP-310N | Service Manual - Page 77
, see the Software Section. Ensure that the paper size in the printer driver settings matches the paper in the tray. Or, ensure that the paper size in the printer driver settings matches the paper selection in the software application settings you use. Service Manual 4-23 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 78
. There may be debris inside the printer. Remove excess paper from the tray. Check that the paper guides are set correctly. Use only paper that meets printer specifications. After opening the front cover, remove the imaging unit and then clear the debris. Service Manual 4-24 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 79
works. Finally, try a new printer cable. Check the application's printer selection menu to ensure that your printer is selected. Try printing a job from another application. Exit Windows and reboot the computer. Turn the printer off and then back on again. Service Manual 4-25 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 80
out of toner. The file may have blank pages. Redistribute the toner. If necessary, replace the toner cartridge. Check the file to ensure that it does not contain blank pages. Some parts in the printer may be defective. Contact a service representative. Service Manual 4-26 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 81
you are using Windows 98, the illustrations print incorrectly from Adobe Illustrator. The setting in the software application is wrong. Select Download as Bit Image in the Advanced Options window of the graphic properties window. Print the document again. Service Manual 4-27 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 82
[Normal] or 600dpi [Draft]. Change the resolution to 2400dpi [Best] and then try printing again. The resolution of the photo is very low. If you increase the photo size in the software application, the resolution will be reduced. Reduce the photo size. Service Manual 4-28 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 83
Alignment & Troubleshooting Description Your printer has an odd smell during initial use. The oil used to protect the fuser is evaporating. After printing about 100 color pages, there will be no more smell. It is a temporary issue. Service Manual 4-29 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 84
print quality, install a new toner cartridge. 2. The paper may not meet paper specifications Check the paper type and quality. 3. A combination of faded or smeared defects may indicate that the printer needs cleaning Check the inside for the printer. Service Manual 4-30 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 85
Alignment & Troubleshooting 2) Toner specks AaBbCc AaBbCc AaBbCc AaBbCc AaBbCc The paper may not meet specifications Check the paper type and quality. Service Manual 4-31 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 86
Alignment & Troubleshooting 3) Dropouts AaBbCc AaBbCc AaBbCc AaBbCc AaBbCc 1. If generally some areas to reject toner. Try a different kind or brand of paper. 4. The toner cartridge may be defective. See "Vertical repetitive defects" on the next page. Service Manual 4-32 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 87
page 2. If white vertical lines appear on the page A imaging unit has probably been scratched. Remove the imaging unit and install a new one. Clean the inside of the printer. If you still have the same problems, replace the imaging unit with a new one. Service Manual 4-33 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 88
the problem. 2. heck the printer's environment Change to lighter weight paper. 1. very dry (low humidity) or high humidity (higher than 80% RH) conditions can increase the amount of background shading. 2. Remove one of the old toner cartridges and install a new one. Service Manual 4-34 Samsung - Samsung CLP-310N | Service Manual - Page 89
6) Toner smear Alignment & Troubleshooting 1. Toner smear 1. Clean the inside of the printer. 2. Check the paper type and quality. 3. Remove the imaging unit and install a new one. Service Manual 4-35 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 90
the same problems, install a new toner cartridge of the problem color. If the defects occur on the back of the page, the problem will likely correct itself after a few more pages. 3. The fusing assembly may be damaged. Contact a service representative. Service Manual 4-36 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 91
much moisture. Change the printing layout to avoid printing over areas that have overlapping seams on the reverse side. Printing on seams can cause problems. Adjust the print resolution through your software application or via the printer properties window. Service Manual 4-37 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 92
are improperly formed and producing hollowed images The paper stock may be too slick. Try a different paper. 2. If characters are improperly formed and producing a wavy effect. The printer may need service. Verify that it also occurs on a demo page. Service Manual 4-38 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 93
& Troubleshooting 1. Page skew Ensure that the paper is loaded properly. 2. The paper may not meed specifications Check the paper type and quality. 3. Ensure that the paper or other material is loaded correctly The guides are not too tight or too loose against the paper stack. Service Manual - Samsung CLP-310N | Service Manual - Page 94
Troubleshooting 1. Curl or wave Ensure that the paper is loaded properly. 2. Check the paper type and quality. Both high temperature and high humidity can cause paper curl. 3. Turn the stack of paper over in the tray. Also try rotating the paper 180¡ in the tray. Service Manual 4-40 Samsung - Samsung CLP-310N | Service Manual - Page 95
& Troubleshooting 12) Wrinkles or creases 1. Wrinkles or creases 2. The paper may not meed specifications 3. Turn the stack of paper over in the paper tray. Ensure that the paper is loaded properly. Check the paper type and quality. Also try rotating the paper 180¡ in the tray. Service Manual - Samsung CLP-310N | Service Manual - Page 96
Alignment & Troubleshooting 13) Back of printouts aredirty Check for leaking toner. Clean the inside of the printer. Service Manual 4-42 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 97
Solid Color or Black pages A 1. The toner cartridge may not be installed properly. Remove the toner cartridge and reinsert. 2. The toner cartridge may be defective and need replacing. Install a new toner cartridge. 3. The printer may require repair. Change HVPS. Service Manual 4-43 Samsung - Samsung CLP-310N | Service Manual - Page 98
The paper may not meed specifications 3. The Toner Cartridge may be defective and need replacing. 4. If the problem persists, the printer may require repair. Check the paper type and quality. Install a new toner cartridge. Contact a service representative. Service Manual 4-44 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 99
Alignment & Troubleshooting A 1. Character voids are white areas within characters that should be solid black 1. You may be printing on the wrong surface of the paper. Remove the paper and turn it over. 2. The paper may not meet paper specifications. Service Manual 4-45 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 100
AaBbCc AaBbCc AaBbCc AaBbCc 1. If horizontally aligned color or black streaks or smears appear A toner cartridge may be installed improperly. Remove the toner cartridge and reinsert. 2. A toner cartridge may be defective. Install a new toner cartridge. Service Manual 4-46 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 101
18) Curl Alignment & Troubleshooting 1. If the printed paper is curled or paper does not feed into the printer Turn the stack of paper over in the paper tray. Also try rotating the paper 180¡ in the tray. Service Manual 4-47 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 102
Alignment & Troubleshooting 4.2.5 Common Windows Problems "File in Use" message appears during installation. "Error Writing to LPTx" message appears. "General Protection Fault", "Exception OE", "Spool32", or "Illegal Operation" messages appear. "Fail To Print", "A printer timeout error occurred." - Samsung CLP-310N | Service Manual - Page 103
Alignment & Troubleshooting 4.2.6 Common Macintosh Problems The printer does not print a document from Acrobat Reader. The document has printed, but the print job has not disappeared from the spooler in Mac OS 10.3.2. You should change the Print Method option to Print as Image when you print from - Samsung CLP-310N | Service Manual - Page 104
& Troubleshooting 4.2.7 Common Linux Problems I can't change settings in the configuration tool. I am using the KDE desktop but the configuration tool and LLPR won't start. I just installed this package but can't find entries in the KDE/ Gnome menus. I get a "Some options are not selected" error - Samsung CLP-310N | Service Manual - Page 105
& Troubleshooting Continue.. I can't make a printer the system default. The N-up setting does not work correctly for some of my documents. I am using BSD lpr (Slackware, Debian, older distributions) and some options chosen in LLPR don't seem to take effect. I am trying to print a document in - Samsung CLP-310N | Service Manual - Page 106
the document may not print correctly. To be able to configure and use SMB-shared printers (such as printers shared on a Windows printer), you need to have a correct installation of are provided as a convenience with this Linux Printing Package. Service Manual 4-52 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 107
even though I don't choose them in LLPR. I configured a printer to print to a file, but I get "Permission denied" errors. On my PCL (or GDI) printer, I sometimes get error messages printing instead of my document. Some color images come out all black. There may be some local options defined in your - Samsung CLP-310N | Service Manual - Page 108
Alignment & Troubleshooting 4.2.8 Major Problems Trouble shooting 1) Vertical Line and Band Description 1. Straight thin black vertical line occurs in the printing. 2. Darj\k black vertical band occur in the printing. 1. Damaged develop roller in the Developer. Deformed Doctor-blade or - Samsung CLP-310N | Service Manual - Page 109
the foreign matter and burr of the exposure window. (Developer cartridge) 1. No. 4. : Open the front cover and check ribs that corresponds to the position of the voids. Remove if found. 2. If the problems are not solved, replace the developer cartridge. Service Manual 4-55 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 110
Alignment & Troubleshooting 3) Light Image Description The printed image is light, with no ghost. 1. Develop roller is stained when the toner of developer cartridge is almost consumed. 2. Ambient temperature is below than 10¡C. Replace the developer cartridge and try to print out. Wait 30 - Samsung CLP-310N | Service Manual - Page 111
Alignment & Troubleshooting 4) Dark Image or black Description The printed image is dark. 1. No charge voltage in the HVPS board. Clean the high voltage charge terminal board and HVPS. 2. Replace the HVPS if not solved by the above direction 1 and 2. Service Manual 4-57 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 112
Troubleshooting 5) Background Description Light dark background appears in whole area of the printing. 1. Does character exist less than 2% per a page, and hasn't it been used long time? 2. Does recycle paper be used? The toner cartridge is basically designed to print 3,000 sheets with 5% image - Samsung CLP-310N | Service Manual - Page 113
Alignment & Troubleshooting 6) JAM 0 Description 1. Paper is not exited from the cassette. 2. Jam-0 occurs if the paper feeds into the printer. 1. printer rand Jam 0 occurs, perform EDC to check feed-sensor of the engine board. Replace the Main B'D and/or Sensor. Service Manual 4-59 Samsung - Samsung CLP-310N | Service Manual - Page 114
Alignment & Troubleshooting 7 JAM 1 Description 1. Recording paper is jammed in front of or inside the fuser. 2. Recording paper is stuck Actuator may be defective. Replace the SMPS. Reassemble the Actuator-Feed and SpringActuator if the returning is bad. Service Manual 4-60 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 115
Alignment & Troubleshooting 8) Multi-Feeding Description Multiple sheets of paper are fed at once. 1. Solenoid malfunction (the solenoid does not work clothe dampened with IPA(Isopropyl Alcohol). 3. The face of paper is blended. Use the smooth paper. Service Manual 4-61 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 116
Alignment & Troubleshooting 9) Not function of the gear of the fuser due to melting away Description The motor breaks away from it's place due to gear melting away. Check the operation of Fuser Erasing Lamp 1. Replace the Fuser. 2. Replace the Main Control board. Service Manual 4-62 Samsung - Samsung CLP-310N | Service Manual - Page 117
Alignment & Troubleshooting 10) Paper Empty Description The paper lamp on the operator panel is on even when paper is loaded in sensor. Replace the defective actuator. 2. The function of the engine board is defective Perform Replace the engine board. Service Manual 4-63 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 118
Alignment & Troubleshooting 11) Cover Open Description The ERROR lamp is on even when the print cover is closed. 1. The Hook Lever in the top cover may be defective. Replace Cover Open S/W Connect. 2. Replace the Main Control board or Cover Open S/W. Service Manual 4-64 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 119
not feed into the printer, resulting 'Jam 0'. 1. Motor harness or sub PCB may be defective. 1. Check the motor harness, replace it, if defective. 2. Check 24V in the SMPS 3. Check Front Cover or Jam cover are opened. 4. Replace the Main PBA, if necessary. Service Manual 4-65 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 120
Alignment & Troubleshooting 13) No Power Description When system power is turned on, all lamps on the operator panel do not come on. if the LED of Panel does not appear after normal warmingup. 1. Replace the control board. 2. Replace the LED-panel. Service Manual 4-66 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 121
Alignment & Troubleshooting 14) Vertical Line Getting Curved Description When printing, vertical line gets curved. 1. If the supply of +24v is unstable in the Main Control board linking with LSU 1. Replace LSU. 2. Replace the Main Control board. Service Manual 4-67 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 122
, With LSU Error SM Message. 1. Foreign matter stuck onto the window of internal lenses of LSU mirror Cleaning foreign matter in LSU mirror 2. Main Controller LSU Part defect Replace Main Controller 3. Micro Switch Harness Replace Micro Switch Harness Service Manual 4-68 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 123
Unit 5-23 5.11 Cartridge Transfer Unit 5-26 5.12 Tank Waste Unit 5-29 5.13 Cassette 5-31 Samsung Clolr Laser Printer CLP-310N The keynote of Product The smallest / The lowest noise High Quality Muti-path CLBP - Model : CLP-31x series - Speed(Color/Mono) : 4/16 ppm(A4). 4/17ppm(Let) - Printing - Samsung CLP-310N | Service Manual - Page 124
and Parts 5.1 Main 5.2 Cover Front 5.3 Cover Top 5.4 Cover Rear 5.5 Transfer Unit 5.6 Frame1 5.7 Frame2 5.8 Main Drive1 5.9 Main Drive2 5.10 Fuser Unit 5.11 Cartridge Transfer Unit 5.12 Cartridge-Drum 5.13 Tank Waste Unit 5.14 Cassette Service Manual 5-2 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 125
5-3 Samsung Electronics Service Manual 15 11 12 13 14 10 0 6-1 6 5 4 6-2 16 8 3 1 26 18 27 17 30 2 9 25 23 24 22 21 29 20 7-1 19 7 7-2 28 31 5.1 Main ExplodedView and Parts - Samsung CLP-310N | Service Manual - Page 126
5.1-17 5.1-18 5.1-19 SEC_code Description CLP-310 series CLP-315 series JC97-03020A JC97-03033A A4 COLOR LASER PRNTER A4 COLOR LASER PRNTER MEA UNIT-FRAME MEA UNIT-COVER TOP JC97-03033C MEA UNIT-COVER TOP JC96-01673A ELA UNIT-TERMINAL TR S JC97-01771A MEA UNIT-TERMINAL S JC44-00164A HVPS JC97 - Samsung CLP-310N | Service Manual - Page 127
SA : SERVICEAVAILABLE, SNA : SERVICE not AVAILABLE QT'y Service Grade 1 SA B 1 SNA A 1 SNA A 1 SA A 1 SA A 1 SA B 1 SNA B 1 SA A 1 SA A 1 SNA A 1 SNA A 1 SNA A 1 SA B 1 SA B 1 SA B Remark 220V 310/315 310N 220V 110V XAZ Service Manual 5-5 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 128
5.2 Cover Front ExplodedView and Parts 0 5 6 1 2 16 11-1 10 11-2 14 17 15 3 18 4 8 12 9 7 13 Service Manual 5-6 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 129
01626A JC63-01626B ELA UNIT-COVER FRONT ELA UNIT-COVER FRONT COVER- -TS JC64-00349A BUTTON-SUPPORT 6107-001404 SPRING CS SNA B 2 SA A Remark Black color Gray color Black color Gray color Black color Gray color Black color Gray color Black color Gray color Service Manual 5-7 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 130
5.3 Cover Top ExplodedView and Parts 0 6 Service Manual 10 3 2 8 1 4 5 7 9 5-8 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 131
UNIT-COVER TOP,Black MEA UNIT-COVER TOP,Gray MEA UNIT-COVER TOP,Gray MEA UNIT-COVER TOP,Black JC63-01593A COVER-TOP,Black 1 SNA A 3 SNA D 2 SA A 1 SNA A 1 SNA A 1 SNA A Remark 315 310 310N 315W 315 310 310N 315W 315 310 315 310 315 310 315 310 315 310 Service Manual 5-9 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 132
5.4 Rear Cover ExplodedView and Parts 1 9 4 7 11 3 12 0 2 8 6 5 10 Service Manual 5-10 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 133
5.4-12 JC68-02037A LABEL-INFORMATION QT'y Service Grade 1 SA A 1 SA A 1 SNA A 1 SNA A 1 SAN B 1 SNA B 1 SNA B 1 SNA B 2 SA B 1 SNA B 1 SA B 1 SNA A 1 SNA A 1 SNA B 1 SA A 1 SNA B 1 SNA A Remark 315 310 315 310 315 310 315 310 Service Manual 5-11 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 134
5.5 Transfer Unit ExplodedView and Parts 15 13 4 8 6 5 2 7 11 1 14 0 9 4 3 Service Manual 5-12 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 135
-001278 SPRING-CS 6107-001246 SPRING-CS JC66-01781A ROLLER-TRANSFER JC66-01743A GEAR-T2 ROLLER QT'y Service Grade 1 SA A 1 SNA A 1 SNA A 1 SNA A 2 SNA A 1 SA B 1 SNA A 1 SNA B 1 SA B 1 SNA B 2 SA B 2 SA B 1 SNA A 1 SA B Remark Service Manual 5-13 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 136
Samsung Electronics Service Manual 5-14 6 43 6 30 7 37 35 62 27 20 41 0 67 6 58 69 45 59 12 36 32 34 64 33 42 5 63 40 9 60 5 26 6 60 56 15 41 56 6 5.6 Frame1 ExplodedView and Parts - Samsung CLP-310N | Service Manual - Page 137
-SUPPORT JC63-01779A SHEET-DEFLECTION JC92-01982A JC92-02003A JC96-04757A JC96-04939A JC97-01771A JC97-02638A PBA SUB-OPE PBA SUB-5V_SWITCH ELA UNIT-PTL LAMP ELA HOU-ITB_OPC MEA UNIT-TERMINAL S MEA UNIT-TERMINAL GND JC97-03028A MEA UNIT-PICK UP ROLL JC97-03030A MEA UNIT-ACT REGI QT'y Service - Samsung CLP-310N | Service Manual - Page 138
Samsung Electronics Service Manual 5-16 47 6 53 0 61 27 29 48 47 28 65 6 68 10 31 54 57 11 49 39 48 46 13 53 55 6 50 25 38 24 52 8 51 9 14 66 6 44 5.7 Frame2 ExplodedView and Parts - Samsung CLP-310N | Service Manual - Page 139
PMO-BUSHING_TR(L) ELA UNIT-SENSOR WASTE MEA UNIT-FRAME EXIT MEA UNIT-PICK UP GEAR JC97-03029A MEA UNIT-GUIDE PICKUP QT'y Service Grade 1 SA 1 SA B 1 SA B 1 SA B 2 SNA A 1 SNA B 1 SNA A 2 SA A 1 SA A 1 SA A 1 SA A 1 SA A Remark Service Manual 5-17 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 140
Samsung Electronics Service Manual 5-18 0 1 20 22 2 17 21 19 31 32 23 43 16 15 25 18 28 30 34 24 33 35 40 37 36 41 48 56 29 26 41 38 42 45 44 32 49 52 54 57 55 3 58 50 14 51 53 5.8 Main Drive1 ExplodedView and Parts - Samsung CLP-310N | Service Manual - Page 141
Description JC96-04750A JC61-02273A JC61-02279A 6002-000440 ELA UNIT-DRIVE MAIN BRACKET-DRIVE MAIN BRACKET-STUD SCREW-TAPPING 1 SNA B 4 SNA B 1 SNA B 1 SNA B 1 SA A 2 SA A 13 SNA B 4 SA B 1 SNA B 1 SNA B 1 SNA B 3 SA B 1 SA B Remark Service Manual 5-19 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 142
and Parts Main Drive1 Parts List SA : SERVICEAVAILABLE, SNA : SERVICE not AVAILABLE Drawer# 5.8-51 5.8-52 5.8-53 5.8-54 5.8-55 RDCN OUT V 6044-000231 RING-E QT'y Service Grade 1 SNA B 1 SNA B 1 SNA B 1 SNA B 1 SNA B 1 SNA A 1 SNA A 2 SA A Remark Service Manual 5-20 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 143
5.9 Main Drive2 ExplodedView and Parts 4 7 8 5 9 0 10 11 12 3 13 Service Manual 5-21 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 144
PBA SUB-DEVEHOME JC61-02372A BUSH-D6/L4 JC47-00019A CLUTCH-DEVE CAM JC66-01720A SHAFT-DEVE CAM JC61-02292A HOLDER-DEVE CAM QT'y Service Grade 1 SA B 1 SNA B 1 SA A 1 SNA B 4 SNA B 1 SNA B 1 SNA A 4 SA B 1 SNA B 1 SNA B 1 SNA B Remark Service Manual 5-22 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 145
Samsung Electronics Service Manual 5-23 2 33 37 28 12 38 30 43 20 37 40 39 41 42 43 29 18 44 16 31 4 24 0 15 21 19 1 34 22 32 26 23 36 27 9 3 6 17 35 14 7 8 5.10 Fuser Unit ExplodedView and Parts - Samsung CLP-310N | Service Manual - Page 146
04781A JC66-01804A JC61-01271A ELA UNIT-FUSER ELA UNIT-FUSER ROLLER-PRESSURE SHAFT SPRING FUSER JC61-02361A GUIDE-INPUT FUSER JC61-02364A GUIDE-OUTPUT FUSER JC61- 1 SNA B 1 SNA B 1 SA A 1 SNA B 1 SNA B 2 SNA B 1 SNA B Remark 220V 110V 220V 110V Service Manual 5-24 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 147
ExplodedView and Parts Fuser Unit Parts List SA : SERVICEAVAILABLE, SNA : SERVICE not AVAILABLE Drawer# 5.10-39 5.10-40 5. 01581A LABEL(P)-CAUTION HOT JC97-03034A MEA-GUIDE PR QT'y Service Grade 1 SA B 1 SNA A 1 SNA - 1 SNA - 2 SNA 1 SNA A Remark Service Manual 5-25 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 148
ExplodedView and Parts 5.11 Cartridge Transfer Unit Service Manual 54 2 7 44 6 39 16 0 2 5-26 49 17 47 46 52-1 16 4 52 19 7 14 48 6 21 26 9 53 9 34 27 51 33 30 32 31 28 29 3 23 40 2 38 50 13 25 18 2 35 35 10 24 11 36 37 2 12 45 42 41 43 22 20 54 2 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 149
Cartridge Transfer Unit Parts List SA : SERVICEAVAILABLE, SNA : SERVICE not AVAILABLE Drawer# SEC_code Description 5.11-0 JC96-04840A CARTRIDGE-TRANSFER QT'y Service COVER-WASTE ITB JC63-01630A COVER-WASTE EXIT JC63-01634A COVER-CLEAN ITB JC66-01083A SHAFT-M-BELT WASTE JC66-01873A DRUM-ITBBELT - Samsung CLP-310N | Service Manual - Page 150
MEA UNIT-ROLL DRV ITB JC66-01771A GEAR-DRIVE ITB JC97-03125A MEA UNIT-ROLL TENSION JC96-04938A ELA HOU-ITB_TEMP QT'y Service Grade 1 SNA B 1 SNA B 1 SNA B 1 SNA B 1 SNA B 1 SNA B 1 SNA B 1 SNA B 1 SNA A 1 SNA D 1 SNA B 1 SNA A 1 SNA A 1 SNA B 1 SNA A 1 SNA A Remark Service Manual 5-28 Samsung - Samsung CLP-310N | Service Manual - Page 151
ExplodedView and Parts 5.12 Tank Waste Unit 4 6 5 1 3 2 2 8 0 7 Service Manual 5-29 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 152
TANK-WASTE UPPER JC67-00269A TANK-WASTE LOWER JC67-00279A CAP-WASTEBOTTLE JC68-01995A LABEL-INFORMATION SA : SERVICEAVAILABLE, SNA : SERVICE not AVAILABLE QT'y Service Grade 1 SA B 1 SNA B 2 SNA A 1 SNA A 1 SNA A 1 SNA B 1 SNA B 1 SNA A 1 SNA A Remark Service Manual 5-30 Samsung - Samsung CLP-310N | Service Manual - Page 153
5.13 Cassette ExplodedView and Parts 9 10 12 3 11 13 14 6 8 0 4 5 1 2 7 Service Manual 5-31 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 154
STOPPER-ADJUSTER QT'y Service Grade 1 SA A 1 SA A 1 SNA B 1 SNA B 1 SA B 1 SA B 1 SA A 1 SA A 2 SNA B 1 SA A 1 SA A 1 SA A 1 SNA A 1 SNA A 1 SNA A 1 SA B 1 SNA - 1 SA A Remark 315 310/310N 315 310/310N 315 310/310N Service Manual 5-32 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 155
System Diagram 6. System Diagram 6.1 Block Diagram Service Manual 6-1 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 156
6-2 Samsung Electronics Service Manual 10p LSU 5p 2p Power Inlet & Switch 16p FFC SMPS 2p 4p Sensor (Deve Home) Sensor (Empty) Sensor (Regi) Ground Wire, 225mm 3p Sensor (Exit) 2p Waste Toner_Tx 2p Waste Toner_Rx 3p Fan(reser ved) 2p out temp Display Panel (LED) BLDC Motor (Main) +24V Cover Open - Samsung CLP-310N | Service Manual - Page 157
6-3 Samsung Electronics Service Manual 1. M ain Board ˩ LSU Unit 1 1 Main Board 16 16 1 + 5V_LSU 2 DGND 3 V DO1_plus 1 1 10 10 FFC, 530 mm 10 10 11 12 1 16 5 FFC, 330 mm 55 LSU Unit 1 + 5V_LSU 2 DGND 3 V DO1_plus 4 V DO1_minus 5 DGND 6 L SU_SH1 7 nHSYNC1 8 DGND - Samsung CLP-310N | Service Manual - Page 158
6-4 Samsung Electronics Service Manual 2. SMPS ˩ Main boar d 12 12 1 2 2 1 SMPS TYPE 2 UL1061 26AWG , 250mm Hiros e DF type first line is black. the reminder line color is red. 15 16 15 16 FU SER_ON + 24VA + 24VA + 24VA +24V +5V +5V +5V 12 34 56 78 9 10 11 12 13 14 15 - Samsung CLP-310N | Service Manual - Page 159
6-5 Samsung Electronics Service Manual 3. Main Board ˩ HVPS 1 1 Main Board 24 24 1 1 24 24 FFC , 700 mm 1 + 24VF 20 DEV_SOL3 21 WASTE_ LED_TX 22 WASTE_LED_ RX 23 FAN_MAIN 24 + 5V_LSU 11 24 24 HVPS Unit 1 + 24VF 2 + 24VF 3 DGND 4 DGND 5 n DEV _EN 6 PWM_DEV_VPP 7 - Samsung CLP-310N | Service Manual - Page 160
6-6 Samsung Electronics Service Manual 4. HVPS ˩ Sensor 1 3 HVPS Board 1 4 1 3 1 + 5V 2 nEXIT 3 DGND 1 +5V 2 Waste_Lamp 3 Waste_Level 4 DGND 1 + 5V 2 nREGI 3 DGND 100 mm 150 mm 175 mm Exit Sensor Toner Rx Toner Tx Regi Sensor 1 + 5V 2 nEXIT 3 DGND 1 +5V 2 - Samsung CLP-310N | Service Manual - Page 161
6-7 Samsung Electronics Service Manual 5. Main Board ˩ BLDC Main Board 1 1 10 10 UL1061 26AWG , 150mm Molex type first line is black. the reminder line color is red. 1 + 24VF 2 + 24VF 3 DGND 4 DGND 5 DGND 6 + 5V 7 nBLDC_MOTOR_EN 8 BLDC_MOT OR_READY 9 PWM_MOT 10 GAIN 1 BLDC - Samsung CLP-310N | Service Manual - Page 162
6-8 Samsung Electronics Service Manual 6. Main Board ˩ OPC Fusible Main Board UL1061 26AWG , 200mm Molex type first line is black. the reminder line color is red. 1 1 1 1 4 4 2 2 contac t c_joint b'd 1 + 5V 2 DGND 1 + 5V 2 DGND OPC Unit System Diagram - Samsung CLP-310N | Service Manual - Page 163
Service Manual 7. Main board ˩ Sensor 1 1 Main Board 3 3 1 1 5 5 1 1 3 3 1 1 2 2 1 1 3 3 Deve Home Sensor ITB Home Sensor Inn er Temp Out Temp Sensor Eraser Empty Sensor System Diagram 6-9 Samsung Electronics 1 + 5V 2 nIT B_HOME 3 DGND 4 INNER T EMP 5 DGND 1 + 5V - Samsung CLP-310N | Service Manual - Page 164
Service Manual 8. Main Board ˩ Crum Joint Main Board 1 1 1 1 UL1061 26AWG , 475mm Cr um Joint 4 4 4 4 board to board 3 SDA 4 DGND Crum M 1 + 3.3V 2 SCL 3 SDA 4 DGND Crum C 1 + 3.3V 2 SCL 3 SDA 4 DGND Crum K 1 + 3.3V 2 SCL 3 SDA 4 DGND Samsung Electronics - Samsung CLP-310N | Service Manual - Page 165
6-11 Samsung Electronics Service Manual 9. Main Board ˩ Actuator 1 1 Main Board 2 2 1 1 3 3 1 1 3 3 1 1 2 2 1 1 2 2 1 1 3 3 1 1 2 2 UL1061 26AWG , mm UL1061 26AWG , mm UL1061 26AWG , mm UL1061 26AWG , mm UL1061 26AWG , mm UL1061 26AWG , mm UL1061 26AWG , - Samsung CLP-310N | Service Manual - Page 166
Service Manual 10. M ain Board ˩ Heater Unit Main Board 1 1 UL1061 26AWG ,200 mm UL1061 26AWG ,150 mm 2 2 1 1 connective connector FFC, 230 mm 8 8 Ther misto r 1 1 Panel 8 8 SMPS 1 1 2 2 UL 18AWG ,550 mm Fuser Unit System Diagram 6-12 Samsung Electronics 1 FUSER_THERM1 - Samsung CLP-310N | Service Manual - Page 167
manual, and a guide to the location space required when installing the printer. A definition of tests pages and Wireless Network information definition is also included. 7.1 Tools for Troubleshooting The following tools are recommended safe and easy troubleshooting as described in this service manual - Samsung CLP-310N | Service Manual - Page 168
Unit Megabyte Megahertz Mean Prints Between Failure Multi Purpose Feeder/Multi Purpose Tray Network Interface Card Network Printer Card Nonvolatile Random Access Memory Organic Photo Conductor Printed Board Assembly Printer Command Language , Printer Control Language Service Manual 7-2 Samsung - Samsung CLP-310N | Service Manual - Page 169
Graphic Processor Samsung Printer Language Samsung Printer Language-Color Simultaneous Peripheral Operation Online Software Requirment Specification Surface Rapid Fusing Switch Synchronous or Synchronization ITB Transfer Roller Toner Reproduction Curve Universal Plug and Play User Interface Uniform - Samsung CLP-310N | Service Manual - Page 170
Reference Information 7.3 Select a location for the printer • Leave enough room to open the printer trays, covers, and allow for proper ventilation. (see diagram below) • Provide the proper of temperature, sunlight, or humidity - Clean, dry, and free of dust Service Manual 7-4 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 171
Reference Information 7.4 A4 ISO 19752 Standard Pattern This test page is reproduced at 70% of the normal A4 size Service Manual 7-5 Samsung Electronics - Samsung CLP-310N | Service Manual - Page 172
GSPN (Global Service Partner Network) North America : service.samsungportal.com Latin America : latin.samsungportal.com CIS : cis.samsungportal.com Europe : europe.samsungportal.com China : china.samsungportal.com Asia : asia.samsungportal.com Mideast & Africa : mea.samsungportal.com ͿSamsung
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
 |
 |
Color Laser Printer
CLP-31
5/XAZ
SERVICE
Manual
Samsung C
olo
r Laser Printer
The keynote of Product
The smallest / The lowest noise
High Quality Muti-path CLBP
- Model : CLP-31x series
- Speed(Color/Mono) : 4/16 ppm(A4). 4/17ppm(Let)
- Printing resolution : Max. 2,400 x 600 dpi
- Emulation : SPL-C
- Memory : 32 MB (Network model : 32MB )
- Processor : 360MHz
- Interface : IEEE 802.3,Ethernet(10/100Mbps)
Wireless: Not Supported
- Toner Cartridge :
1.5K Toner(K), 1K toner(C, M, Y each)
- Printer Life : 100,000 pages
Monthly Max. Duty : 20,000 pages/month
Basic Model : CLP-310N,CLP-315
CLP-310N