Samsung DV50F9A6GVW/A2 User Manual Installation Guide Included Ver.1.0 (Englis - Page 30

Vent Sensor Dv50f9a8eg

Get Samsung DV50F9A6GVW/A2 PDF manuals and user guides View all Samsung DV50F9A6GVW/A2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

operating instructions, tips VENT SENSOR (DV50F9A8E(G)*) Your Samsung dryer is equipped with a Vent Sensor, which detects and notifies you when it is time to clean the ductwork. Keep your dryer safe and efficient by cleaning the ducts when prompted. The Vent Sensor detects any duct blockages You can fi gure out whether there is a duct blockage from the "Vent Sensor " lamp of the digital display. Level 0 1 Message The "Vent Sensor " lamp is turned off . The "Vent Sensor " lamp illuminates. Status Solution The ductwork is free from blockages. When a part of the duct or the lint fi lter is blocked by lint or a foreign object. When the resistance is high because the duct is too long or bent. Check the duct connection and shorten the duct and straighten it if necessary. Check the lint fi lter or the duct and clean it if necessary. 2 The "Vent Sensor " When the duct is blocked Check the duct lamp blinks. by lint or a foreign object. connection and shorten When the resistance is the duct and straighten it very high because the if necessary. duct is too long or bent Check the lint fi lter or the excessively. duct and clean it as soon as possible. In the LEVEL 2 state, this lamp blinks for 3 hours after the completion of the cycle. (If the wrinkle prevention function is activated, this message is displayed for up to 3 hours.) If the power button is pressed or the door is opened, the power is immediately turned off. For more information about the duct installation, please refer to the "Ducting requirements" section on page 10. • Although the dryer is available even if the blockage message is displayed, the drying time may be extended. • If the LEVEL 1 message is displayed the fi rst time the dryer is run after the installation, check the connection and clean the duct. If the LEVEL 1 message appears even after you have checked and cleaned the ducts, this may indicate that there are some restrictions of the duct due to the length, condition, etc. If this occurs, you can use the dryer normally and no countermeasures need to be taken. However, the drying time may be extended or the drying performance may be degraded. 30_ operating instructions, tips '"%3:@%7'@64&3."/6 JOEE

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
30_
operating instructions, tips
VENT SENSOR (DV50F9A8E(G)*)
Your Samsung dryer is equipped with a Vent Sensor, which detects and notifies you when it is time to clean
the ductwork. Keep your dryer safe and efficient by cleaning the ducts when prompted.
The Vent Sensor detects any duct blockages
You can fi gure out whether there is a duct blockage from the “Vent Sensor ” lamp of the
digital display.
Level
Message
Status
Solution
0
The “Vent Sensor
”
lamp is turned off .
The ductwork is free from
blockages.
-
1
The “Vent Sensor
”
lamp illuminates.
When a part of the duct
or the lint fi lter is blocked
by lint or a foreign object.
When the resistance is
high because the duct is
too long or bent.
Check the duct
connection and shorten
the duct and straighten it
if necessary.
Check the lint fi lter or
the duct and clean it if
necessary.
2
The “Vent Sensor
”
lamp blinks.
When the duct is blocked
by lint or a foreign object.
When the resistance is
very high because the
duct is too long or bent
excessively.
Check the duct
connection and shorten
the duct and straighten it
if necessary.
Check the lint fi lter or the
duct and clean it as soon
as possible.
In the LEVEL 2 state, this lamp blinks for 3 hours after the completion of the cycle. (If the wrinkle
prevention function is activated, this message is displayed for up to 3 hours.)
If the power button is pressed or the door is opened, the power is immediately turned off.
For more information about the duct installation, please refer to the “Ducting requirements”
section on page 10.
• Although the dryer is available even if the blockage message is displayed, the drying time
may be extended.
• If the LEVEL 1 message is displayed the fi rst time the dryer is run after the installation,
check the connection and clean the duct. If the LEVEL 1 message appears even
after you have checked and cleaned the ducts, this may indicate that there are some
restrictions of the duct due to the length, condition, etc.
If this occurs, you can use the dryer normally and no countermeasures need to be taken.
However, the drying time may be extended or the drying performance may be degraded.
operating instructions, tips
F900A DRY_DV50F_USER MANUAL_DC68-03170D_EN（邀请翻译成 法语+西班牙语）.indd
30
2013-1-25
9:26:54