Samsung DVG45T6000W/A3 User Manual - Page 29

Vent blockage test, Running the vent blockage test

Get Samsung DVG45T6000W/A3 PDF manuals and user guides View all Samsung DVG45T6000W/A3 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

Installation Vent blockage test After the dryer is installed, start the Vent Blockage Test to check if the duct system is properly installed. The Vent Blockage Test automatically detects the status of the ducts and reports any blockage or problems. Proper ducting can reduce drying time and save energy. NOTE The Vent Blockage Test must run when the dryer is cool. If the dryer warms up after the installation check, run the AIR FLUFF cycle for several minutes to reduce its internal temperature. Running the vent blockage test 1. Make sure the drum is empty, and then close the door. (If there are any clothes or other items in the drum, the test will not give accurate results.) 2. Press the Power button to turn the dryer on, then simultaneously press and hold the Adjust Time and Dryness buttons for 3 seconds. "InS" appears in the dryer's display. (If you have started other procedures before the Vent Blockage Test, the dryer will not enter the Vent Blockage Test mode.) 3. Press the Start/Pause (Hold to Start) button. The Vent Blockage Test starts immediately. During the test, the number indicator makes a circle in 6 clockwise steps. The test takes about 2 minutes. Do not open the door during the test. 4. After 2 minutes, when the test is complete, the results are displayed and the dryer sounds a tone. If status of the duct system is normal, "0" appears and the dryer sounds a completion tone. If the duct system cannot exhaust properly, the check code appears, and the dryer sounds an alarm tone. For description about the code, see the "Installation check codes" section on page 30. If there are any other problems, an information code appears in the display. For description about the code, see the "Information codes" section on page 51. - To stop or cancel the Vent Blockage Test, press the Power button to turn off your dryer. - The results remain on the display for about 5 minutes and then automatically turn off. You can turn the results off immediately by pressing the Power button. Untitled-10 29 English 29 2020-07-14 3:22:16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
English
29
Installation
Vent blockage test
After the dryer is installed, start the Vent Blockage Test to check if the duct system is
properly installed. The Vent Blockage Test automatically detects the status of the ducts
and reports any blockage or problems. Proper ducting can reduce drying time and save
energy.
NOTE
The Vent Blockage Test must run when the dryer is cool. If the dryer warms up after
the installation check, run the
AIR FLUFF
cycle for several minutes to reduce its internal
temperature.
Running the vent blockage test
1.
Make sure the drum is empty, and then close the door. (If there are any clothes or
other items in the drum, the test will not give accurate results.)
2.
Press the
Power
button to turn the dryer on, then simultaneously press and hold the
Adjust Time
and
Dryness
buttons for 3 seconds. “
InS
” appears in the dryer’s display.
(If you have started other procedures before the Vent Blockage Test, the dryer will not
enter the Vent Blockage Test mode.)
3.
Press the
Start/Pause (Hold to Start)
button. The Vent Blockage Test starts immediately.
During the test, the number indicator makes a circle in 6 clockwise steps. The test takes
about 2 minutes. Do not open the door during the test.
4.
After 2 minutes, when the test is complete, the results are displayed and the dryer
sounds a tone. If status of the duct system is normal, “
0
” appears and the dryer sounds
a completion tone.
If the duct system cannot exhaust properly, the check code appears, and the dryer
sounds an alarm tone. For description about the code, see the “
Installation check codes
”
section on page
30
.
If there are any other problems, an information code appears in the display. For
description about the code, see the “
Information codes
” section on page
51
.
-
To stop or cancel the Vent Blockage Test, press the
Power
button to turn off your
dryer.
-
The results remain on the display for about 5 minutes and then automatically turn
off. You can turn the results off immediately by pressing the
Power
button.
Untitled-10
29
2020-07-14
°° 3:22:16