Samsung DW80R5061 User Manual - Page 13

Installing The Dishwasher

Get Samsung DW80R5061 PDF manuals and user guides View all Samsung DW80R5061 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

02 INSTALLING THE DISHWASHER 1 2 A 3 E CD B F 1) Disconnect the 90° fitting (A) from the hose (B). 2) Remove the seal (C) and the nut (D) from the 90° fitting. 3) From the provided nut connector, separate the seal (E) and the nut (F), and then assemble them to the 90° fitting as shown in the figure. You must insert the smaller side of the seal. 4. Then, insert the ¾" 90 degree fitting into the inlet valve (see Figure 4-B). Tighten until the ¾" fitting is tight. Do not over tighten. 5. Make sure there are no kinks and that the hose is not bent at any extreme angles that could constrict the flow of water. 6. Remove the junction box cover located at the bottom front right of the dishwasher using a screwdriver, and then Install the strain relief (Figure 4 - C). Make sure to keep the junction box cover you removed. It is used in Step 11, Wiring Connections. 7. If the countertop is made of wood or a material that is not damaged by drilling, attach the two (2) Installation brackets that were supplied with the dishwasher using the supplied screws (Figure 4 - A). They will be used in Step 9, Securing the Dishwasher. A Junction box C Strain relief B CAUTION Do not overtighten the 90˚ elbow. (Below 280 lb·in (31.6 N·m)) Doing so may damage the water inlet valve and cause a water leak. Hot Water Supply Line Elbow( 3/4" (9.5 mm)) Inlet valve installing the dishwasher _13 Installation_DD81-02034B-02_EN.indd Sec3:13 2/51/0/82/0210617 101:05:65:60:303AAMM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
installing the dishwasher
_13
02 INSTALLING THE DISHWASHER
Make sure there are no kinks and that the hose is not bent at any extreme angles that could
constrict the flow of water.
Remove the junction box cover located at the bottom front right of the dishwasher using a
screwdriver, and then Install the strain relief (Figure 4 - C). Make sure to keep the junction box
cover you removed. It is used in Step 11, Wiring Connections.
.
If the countertop is made of wood or a material that is not damaged by drilling, attach the
two (2) Installation brackets that were supplied with the dishwasher using the supplied
screws (Figure 4 - A). They will be used in Step 9, Securing the Dishwasher.
<Figure 4>
A
C
B
Junction box
Strain relief
CAUTION
Do not overtighten the 90˚ elbow.
(Below 280 lb·in (31.6 N·m))
Doing so may damage the water inlet valve
and cause a water leak.
Installation_DD81-02034B-02_EN.indd
Sec3:13
Installation_DD81-02034B-0
_EN.indd Sec3:13
/10/2016 10:56:03 AM
25/08/2017
10:56:03 AM
2
1
2
3
A
B
C
E
F
D
1)
Disconnect the 90° fitting (A) from the hose (B).
2)
Remove the seal (C) and the nut (D) from the 90° fitting.
3)
From the provided nut connector, separate the seal (E) and the nut (F), and then
assemble them to the 90° fitting as shown in the figure. You must insert the smaller side
of the seal.
4.
Then, insert the ¾" 90 degree fitting into the inlet valve (see Figure 4-B). Tighten until the ¾"
fitting is tight. Do not over tighten.
5.
6.
7
Hot Water Supply Line
Hot Water Supply Line
Elbow( 3/4" (9.5 mm))
Elbow( 3/4" (9.5 mm))
Inlet valve
Inlet valve