Samsung HP-P5581 Quick Guide (easy Manual) (English) - Page 2

Operation Selecting a broadcast source Before your television can begin memorizing the available channels, you must specify the type of signal source that is connected to the TV (i.e., an antenna or a cable system). Press the MENU button. Press the ... or † button to select "Channel", then press the ENTER button. TV Channel Antenna : Air √ Auto Program √ Add / Delete √ Favorite Channels √ Name √ Fine Tune √ † More Move Enter Return Press the ... or † button to select "Auto Program", then press the ENTER button. TV Channel Antenna : Air √ Auto Program √ Add / Delete √ Favorite Channels √ Name √ Fine Tune √ † More Move Enter Return Press the ... or † button to select the antenna connection, then press the ENTER button. NOTES • Air : "Air" antenna signal. • Cable : "Cable" antenna signal. • Air+Cable : "Air" and "Cable" antenna signals. If the CableCARD is inserted into the "CableCARD" slot on the rear panel, "Cable" and "Air+Cable" are not available. When selecting Cable TV system : Press the ... or † button to select "Cable", then press the ENTER button. Press the ... or † button to select "STD", "HRC", or "IRC", then press the ENTER button. TV Auto Program Select the antennas to memorize Air Start Cable Start Air + Cable Start Move Enter Return TV Auto Program Select the antennas to memorize Air Start Cable Start Air + Cable Start Move Enter Return Storing Channels in Memory (Automatic Method) Press the ... or † button to select the antennas to memorize. Press the ENTER button to select "Start". TV Auto Program Select the antennas to memorize Air Start Cable Start Air + Cable Start Move Enter Return Press the ENTER button to start the auto program. The TV begins memorizing all available stations. Press the ENTER button at any time to interrupt the memorization process. Press the EXIT button to exit. Auto Program Channel Memory in Process AIR Channel 67 Stop Enter Return NOTE • The TV must be connected to an antenna in order to receive digital TV signals. Even if a particular channel is deleted from the memory, you can always tune to that channel directly by using the number buttons on the remote control. NOTES • All available DTV and analog channels are automatically stored in memory when channels are selected by the direct tuning function. • It takes approximately 3 to 10 minutes to memorize channels. NOTE • STD, HRC, and IRC identify various types of cable TV systems. Contact your local cable company to identify the type of cable system that exists in your particular area. At this point the signal source has been selected. Proceed to "Storing Channels in Memory". TV Auto Program Select the cable system. STD HRC IRC Move Enter Return Front Panel Information Window ' Œ SOURCE button Press to display all of the available video sources (TV, AV1, AV2, S-VIDEO1, S-VIDEO2, COMPONENT, DVI, and HDMI). ´ MENU button Displays the main on-screen menu. ˇ VOL(+,-) button Press to increase or decrease the volume. Also used to select or adjust items on the on-screen menu. ¨ CH( , ) button Press CH or CH to change channels. Also used to move up or down in the on-screen menu. Œ ´ ˇ ¨ ˆ Ø " ∏ TOUCH button Touch the right side of each button to operate. ˆ ENTER( ) button Press to confirm a selection. Ø Power Indicator - Power Off - Power On - Timer On : Red : Off : Green ∏ Press to turn the PDP on and off. " Remote Control Signal Receiver Aim the remote control towards this spot on the PDP. ' Speakers BN68-00766A Quick Guide Remote Control Buttons Remote Control Œ POWER button Turns the PDP on and off. ´ ANTENNA button Press to select "AIR" or "CABLE". ˇ Number buttons ¨ - button Press to select additional channels (digital and analog) being broadcast by the same station. For example, to select channel "54-3", press "54", then press "-" and "3". ˆ MUTE button Press to mute the PDP sound. Ø VOL (Volume) buttons Use to adjust volume. ∏ GUIDE button Press to display the on-screen Electronic Program Guide (EPG). " MENU button Displays the main on-screen menu. ' ENTER button Confirms a selection. ˝ FAV. CH button Press to switch to your favorite channels. Ô CH. LIST Displays the channel list.  LCD Display When you press a button, ' ' appears along with selected mode (TV, VCR, CATV, DVD, or STB) and the remote's battery charge status. Ò P.MODE button Adjusts the PDP picture by selecting one of the preset factory settings (or select your personal, customized picture settings). Ú MODE button Selects a target device to be controlled by the Samsung remote control (i.e., VCR, Cable box, DVD players, or Samsung STB). If you change modes, the new mode is momentarily displayed on LCD. Æ PRE-CH button Tunes to the previous channel. ı SOURCE button Press to display all of the available video sources (TV, AV1, AV2, S-VIDEO1, S-VIDEO2, COMPONENT, DVI, and HDMI). ˜ CH (Channel) buttons Use to switch channels. ¯ INFO button Press to display information on the PDP screen. ˘ EXIT button Press to exit the menu. ¿ Up/Down Left/Right buttons Control the cursor in the menu. ¸ MTS button Press to choose stereo, mono or Separate Audio Program (SAP broadcast). ˛ PIP button Activates picture in picture. ◊ ASPECT button Press to change the screen size. ± STILL button Press to pause the current screen. ≠ DNIe button Activates DNIe (Digital Natural Image engine). - SRS button Selects TruSurround XT mode. - SET button Used during set up of this Samsung remote control, so that it will work compatibly with other devices (VCR, Cable Box and DVD). ÷ SLEEP button Press to select a preset time interval for automatic shut off. ® PIP control buttons CH , : Press to change PIP channels. (Only Analog channels can be viewed through PIP.) ∑ CAPTION button Controls the caption decoder. µ VCR, DVD control buttons Controls VCR tape or DVD disc functions: Stop, Rewind, Play/Pause, and Fast Forward. ¥ RESET button If your remote control is not functioning properly, take out the batteries and press the reset button for about 2~3 seconds. Re-insert the batteries and try using the remote control again.