Samsung LN46E550F6F Quick Guide Easy Manual Ver.1.0 (English) - Page 1
Samsung LN46E550F6F Manual
View all Samsung LN46E550F6F manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
USB2 HDMI IN 4 Quick Setup Guide Congratulations on the purchase of your new Samsung TV. Read this setup guide to get your TV up and running quickly. Step 3 : Connect External Devices Connecting an AV device (Blu-ray player, cable/satellite box, etc.) For the very best picture quality, select HD signal sources and use HDMI cables and connections. Note that many digital cable programs are not in HD. Check with your video provider to ensure your devices are receiving HD signals. AV IN 2 HD connection (up to 1080p) USB2 Using an HDMI Cable HDMI OUT Device (HDD) USB1 HDMI IN 4 STOP Please do not return this unit. If you have problems operating your TV, call: 1-800-SAMSUNG (1-800-726-7864) For web support please visit: www.samsung.com/support 1-800-SAMSUNG (1-800-726-7864) Samsung Electronics America, Inc. 85 Challenger Road Ridgefield Park, NJ 07660-2112 Samsung Electronics Canada Inc. 55 Standish Court Mississauga, Ontario L5R 4B2 Call Center hours of operation: Mon-Sun, 9:00 AM -12 AM EST. To register this product, visit : www.samsung.com/register. Getting Started Step 1 : Install the Batteries into the Remote To install batteries into your remote control, follow these steps: 1. Lift the cover on the back of the remote upward as shown in the figure to the right. 2. Install two AAA batteries. ✎✎ Make sure to match the + and - ends of the batteries to the diagram in the battery compartment. 3. Replace the cover. AV IN 2 Audio/Video connection (480i only) Using an Audio/Video Cable VIDEO OUT AUDIO OUT VCR / DVD / Blu-ray player / Cable Box / Satellite receiver Lowest Quality Connection (HDD) USB1 HDMI IN 4 USB2 The HDMI connection carries digital video and audio. (HDD) USB1 DVD / Blu-Ray player / HD Cable Box / HD Satellite receiver (STB) AV IN 2 Best Connection USB2 HDMI IN 4 HD connection (up to 1080p) Using a DVI to HDMI Cable (HDD) USB1 DVI OUT Device AV IN 2 DVD / Blu-Ray player / Cable Box / Satellite receiver (STB) Very Good Connection Component connection (up to 1080p) Using a Component Cable AUDIO OUT COMPONENT OUT Blu-ray player VCR / DVD / Blu-ray player / Cable Box / Satellite receiver Good Connection Step 2 : Connect Power and Antenna or Cable Connect ANT IN to: • Wall cable jack or • VHF/UHF Antenna or • Cable or Satellite box Ant or Cable Out or Use a 75 ohm (round) cable. Power Input Step 4 : Run Plug & Play When you turn on your TV for the first time, it automatically launches the Plug & Play function. With Plug & Play, you can select the On Screen Display language, set the clock mode, and launch the TV's channel memorizing process. It also displays connection instructions similar to those in this guide. To navigate while Plug & Play is running, press the Up, Down, Left or Right arrow buttons on your remote. To make a selection, press the ENTERE button. To skip a screen, press the MENU button. To turn on your TV, press the POWER button on the remote or press the POWER button on the TV. To run Plug & Play, follow these steps: Make sure the AC power cord is plugged in securely to the wall outlet and the TV. Plug & Play Select Language of the OSD. English 1 Language E: Esnpgalñisohl Français AV IN 2 (HDD) USB1 HDMI IN 4 USB2 U Move E Enter On the Language screen, select the language for the On Screen Display (OSD) using your remote control, and then press ENTERE button. The Home Use screen appears. Plug & Play Select 'Home Use' when installing this TV in your home. 2 Store Demo Home Use L Move E Enter Select Home Use, and then press ENTERE button. If you select Store Demo, the TV will reset your picture and audio settings every 30 minutes. After you press ENTERE button , the Antenna Source screen appears. Plug & Play Select the Antenna source to memorise. 3 Air Cable Start Start Auto Start U Move E Enter m Skip If your TV is only attached to an antenna, select Air. If your TV is only attached to cable and you have no cable box, select Cable. If your TV is attached to an antenna and cable with no box, select Auto. When done, press ENTERE button on your remote. The Select Cable System screen appears. IMPORTANT: If your TV is attached to a cable or satellite box, skip Steps 3 through 5. After Plug & Play is complete, set your TV to Channel 3 or 4, according to the directions for your cable or satellite box. Plug & Play Selects the cable system. 4 Analog STD HRC IRC Digital STD HRC IRC Start U Move E Enter m Skip If your TV is attached to a cable system and you have no cable box, you must select your cable system type. If you have Digital cable, you must select the cable system type for both Analog and Digital. After you have selected the cable system type, select Start, and then press the ENTERE button on your remote. ✎✎ Most cable systems are Standard (STD) systems. If you are not sure about what kind of cable system you have, contact your cable company. Plug & Play Auto Program in Progress. 5 DTV Cable : -- Cable : -- Cable 28 15% Stop E Enter m Skip The TV memorizes the available channels. This process can take up to 45 minutes. Plug & Play Set the Clock Mode. 6 Clock Mode Auto : English Manual After the time zone screen, The connection method for best HD screen quality is displayed. Press Right 8 arrow button on your remote to view each screen in succession. Press the MENU button to skip this section. The Enjoy your TV screen 9 appears. Then press ENTERE button. U Move E Enter m Skip After the TV has memorized the channels, choose the Clock Mode. Select Auto if you have a digital channel in your area. Select Manual if you don't, or if you have a cable or satellite box. When done, press ENTERE button. ✎✎ If you select Manual, the clock setting screen appears. Plug & Play Set to daylight saving time. 7 DST Off O: Ennglish Auto U Move E Enter m Skip Select the daylight savings time setting: Off, On, or Auto, and then press ENTERE button. [LD550-QSG]BBN68-04314A-Eng.indd 1 English - 1 2012-02-23 �� 1:42:04