Samsung LN55C630K1F Quick Guide (easy Manual) (ver.1.0) (English) - Page 1
Samsung LN55C630K1F Manual
UPC - 036725233553
View all Samsung LN55C630K1F manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
USB2 USB2 HDMI IN 4 HDMI IN 4 Quick Setup Guide Congratulations on the purchase of your new Samsung TV. Read this setup guide to get your TV up and running quickly. STOP Please do not return this unit. If you have problems operating your TV, call: 1-800-SAMSUNG (1-800-726-7864) For web support please visit: www.samsung.com/support 1-800-SAMSUNG (1-800-726-7864) Samsung Electronics America, Inc. 85 Challenger Road Ridgefield Park, NJ 07660-2112 Samsung Electronics Canada Inc. 55 Standish Court Mississauga, Ontario L5R 4B2 Call Center hours of operation: Mon-Sun, 9:00 AM -12 AM EST. To register this product, visit: www.samsung.com/register. Getting Started Step 1 : Install the Stand (40~55 inch TVs) Follow the steps below to connect the TV to the stand. ✎✎ Make sure to distinguish between the front and back of the Stand and Guide Stand when assembling them. ✎✎ Make sure that at least two people lift and move the LCD TV. ✎✎ Stand the product up and fasten the screws. If you fasten the screws with the LCD TV placed down, it may lean to one side. 1 Guide Stand 2 Step 4 : Connect External Devices (HDD) USB1 Connecting an AV device (Blu-ray player, cable/satellite box, etc.) For the very best picture quality, select HD signal sources and use HDMI cables and connections. Note that many digital cable programs are not in HD. Check with your video provider to ensure your are receiving HD signals. AV IN 2 HD connection (up to 1080p) USB2 Using an HDMI Cable HDMI OUT Device Connecting an audio device Connect your TV to your Home Theater or other audio device to enjoy enhanced sound quality. HDMI IN 4 The HDMI connection carries digital video and audio. DVD / Blu-Ray player / HD Cable Box / HD Satellite receiver (STB) AV IN 2 Best Connection (HDD) USB1 USB2 HDMI IN 4 HD connection (up to 1080p) Using an DVI to HDMI Cable (HDD) USB1 DVI OUT Device AV IN 2 USB2 HDMI IN 4 AUDIO OUT DVD / Blu-Ray player / Cable Box / Satellite receiver (STB) Connecting a PC Connect your TV to a PC to use it as a Monitor. (HDD) USB1 Very Good Connection AV IN 2 Component connection (up to 1080p) Using a Component Cable AUDIO OUT COMPONENT OUT Device AV IN 2 Analog Audio connection Using an Audio Cable AUDIO IN Device Amplifier / DVD Home Theater Digital Audio connection Using an Optical Cable Digital Audio System OPTICAL HD connection Using an HDMI Cable AUDIO OUT DVI OUT PC (HDD) USB1 Stand Screw Top View Bottom View Audio/Video connection (480i only) Using an Audio/Video Cable VIDEO OUT AUDIO OUT VCR VCR / DVD / Blu-ray player / Cable Box / Satellite receiver ✎✎ When connecting to AV IN 1 on the back of your TV, attach the video cable (yellow) to the green jack next to the AV In 1 label. The jack will not match the color of the video cable (yellow). VCR / DVD / Blu-ray player / Cable Box / Satellite receiver Good Connection 3 Lowest Quality Connection Front Rear Step 2 : Install the Batteries into the Remote To install batteries into your remote control, follow these steps: 1. Lift the cover on the back of the remote upward as shown in the figure to the right. 2. Install two AAA batteries. ✎✎ Make sure to match the + and - ends of the batteries to the diagram in the battery compartment. 3. Replace the cover. Step 3 : Connect Power and Antenna or Cable Power Input Connect Ant In to: or Use a 75 ohm (round) cable. • Wall cable jack or • VHF/UHF Antenna or • Cable or Satellite box Ant or Cable Out Make sure the AC power cord is plugged in securely to the wall outlet and the TV. Step 5 : Run Plug & Play When you turn on your TV for the first time, it automatically launches the Plug & Play function. With Plug & Play, you can select the On Screen Display language, set the clock mode, and launch the TV's channel memorizing process. It also displays connection instructions similar to those in this guide. To navigate while Plug & Play is running, press the Up, Down, Left or Right arrow buttons on your remote. To make a selection, press the EnterE button. To skip a screen, press the Menu button. To turn on your TV, press the Power button on the remote or press the Power button on the TV. To run Plug & Play, follow these steps: Plug & Play Select Language of the OSD. English Language : EnEgslpisahñol Français U Move E Enter 1. On the Language screen, select the language for the On Screen Display (OSD) using your remote control, and then press EnterE button. The Home Use screen appears. 2. Select Home Use, and then press EnterE button. If you select Store Demo, the TV will reset your picture and audio settings every 30 minutes. After you press EnterE button, the Antenna Source screen appears. 3. If your TV is only attached to an antenna, select Air. If your TV is only attached to cable and you have no cable box, select Cable. If your TV is attached to an antenna and cable with no box, select Auto. When done, press EnterE button on your remote. The Select Cable System screen appears. IMPORTANT: If your TV is attached to a cable or satellite box, skip Steps 3 through 5. After Plug & Play is complete, set your TV to Channel 3 or 4, according to the directions for your cable or satellite box. 4. If your TV is attached to a cable system and you have no cable box, you must select your cable system type. If you have Digital cable, you must select the cable system type for both Analog and Digital. After you have selected the cable system type, select Start, and then press the EnterE button on your remote. ✎✎ Most cable systems are Standard (STD) systems. If you are not sure about what kind of cable system you have, contact your cable company. 5. The TV memorizes the available channels. This process can take up to 45 minutes. After the TV has memorized the channels, the Clock Mode screen appears. 6. Choose the Clock Mode. Select Auto if you have a digital channel in your area. Select Manual if you don't, or if you have a cable or satellite box. When done, press EnterE button. The Daylight Savings screen appears. ✎✎ If you select Manual, the clock setting screen appears. 7. Select the Daylight Saving Time setting: Off, On, or Auto, and then press EnterE button. 8. After the time zone screen, The connection method for best HD screen quality is displayed. Press Right arrow button on your remote to view each screen in succession. Press the Blue button to skip this section. 9. The Enjoy your TV screen appears. and then press EnterE button. Basic Functions Changing the Screen Size Your TV has several screen size options, each designed to work best with specific types of video input. If you have a cable box or satellite receiver, it may have its own set of screen sizes as well. To change the screen size, press the P.Size button on your remote. The first time you press it, your TV displays the current setting. Thereafter, each time you press the P.Size button, you change the size of the picture on the screen. The following sizes are available: Using an D-Sub Cable PC OUT AUDIO OUT PC 16:9 Wide screen Zoom 1 Zoom 2 Wide Fit 4:3 Standard screen Screen Fit ✎✎ Screen Fit displays a full HD picture covering the entire screen with no cutoff on any side. It is only available when your TV inputs an HDMI (720p, 1080i, 1080p), Component (1080i, 1080p), or DTV (over-the-air 1080i) signal. Changing the Picture Mode Your TV has four preset Picture Modes with factory adjusted settings, each designed to give you an excellent picture under specific conditions. The Picture Modes are listed and described in the table below: Mode Dynamic Standard Natural Movie Description Brightens picture. For a vibrant, enhanced image in brightly lit or sunny room. For a bright, detailed picture in a normally lit room. For a comfortable, easy-on-the-eyes picture in a normally lit room. For a studio quality cinema picture in a dimly lit or dark room. To change the Picture Mode, follow these steps: 1. With the TV on, press the Tools button on your remote. The Tools menu appears. 2. Using the ▲ or ▼ on your remote, select Picture mode. 3. On the Picture Mode menu, use the ◄ or ► on your remote to select the Picture Mode you want. 4. Press the Exit button to exit the menu. English - 1