Samsung ME17R7021ES/AA Installation Guide - Page 14

C. Outside Back Exhaust Horizontal Duct

Get Samsung ME17R7021ES/AA PDF manuals and user guides View all Samsung ME17R7021ES/AA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

Step-by-step installation guide C. OUTSIDE BACK EXHAUST (HORIZONTAL DUCT) C1. ADAPTING MICROWAVE BLOWER FOR OUTSIDE BACK EXHAUST 1. Remove and save screw that holds blower Plate to microwave. Blower Retaining Screws Back of Microwave Oven 2. Open the blower door by lifting it up at the back of the microwave. Remove and save the blower shield on the back of the microwave by sliding it up. Remove and save the metal vent fan cover on the back of the microwave by sliding it up. 3. Carefully pull out the blower unit. The wires will extend far enough to allow you to adjust the blower unit. BEFORE: Fan Blade Openings Facing Forward End B End A CAUTION: Do not touch blade of blower to prevent cracking and breaking. Hold outer case when the blower is removed and re-installed. (On Some model) 4. Remove Parts "A" with tin snips or pliers. Parts "A" 5. Rotate blower unit counterclockwise 180 °. Before Rotation After Rotation Back of Microwave Back of Microwave 6. Place the blower unit back into the opening. AFTER: Fan Blade Openings Facing Back End A End B CAUTION: Do not pull or stretch the blower unit wiring. Make sure the wires are not pinched. NOTE: The blower unit exhaust openings should match exhaust openings on rear of microwave oven. 7. Close the blower door. Slide blower shield onto the top of the blower door opening. Secure the blower to the microwave oven using the blower retaining screws from Step 1 except the upper blower motor retaining screw. Blower Retaining Screw Blower Shield Blower Retaining Screw Back of Microwave Oven 8. Slide the exhaust adaptor onto the back of the microwave oven, securing it into the lower locking tabs. Take care to ensure that the damper hinge is installed so that it is at the top and that the damper swings freely. Reinstall the upper blower motor screw through the adaptor and the blower door and into the back of the microwave oven. Back of Microwave Oven Guide Locking Tabs Adaptor (not shown) Guide Blower Motor Door Retaining Screw 14 ME4000R_ME17R7021EB_AA_DE68-04584A-00_EN.indd 14 6/19/2019 4:17:43 PM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
14
Step-by-step installation guide
C. OUTSIDE BACK EXHAUST (HORIZONTAL DUCT)
C1. ADAPTING MICROWAVE BLOWER
FOR OUTSIDE BACK EXHAUST
1
.
Remove and save screw that holds blower Plate
to microwave.
Back of
Microwave Oven
Blower
Retaining
Screws
2
.
Open the blower door by lifting it up at the back
of the microwave. Remove and save the blower
shield on the back of the microwave by sliding it
up. Remove and save the metal vent fan cover
on the back of the microwave by sliding it up.
3
.
Carefully pull out the blower unit. The wires will
extend far enough to allow you to adjust the
blower unit.
BEFORE: Fan Blade
Openings Facing Forward
End B
End A
CAUTION
:
Do not touch blade of blower to prevent
cracking and breaking. Hold outer case when the
blower is removed and re-installed.
(On Some model)
4
. Remove Parts “A” with tin snips or pliers.
Parts “A”
5
.
Rotate blower unit counterclockwise 180 °.
Before Rotation
After Rotation
Back of Microwave
Back of Microwave
6
.
Place the blower unit back into the opening.
AFTER: Fan Blade Openings
Facing Back
End B
End A
CAUTION
:
Do not pull or stretch the blower unit
wiring. Make sure the wires are not pinched.
NOTE: The blower unit exhaust openings should
match exhaust openings on rear of microwave oven.
7
.
Close the blower door. Slide blower shield onto
the top of the blower door opening. Secure the
blower to the microwave oven using the blower
retaining screws from Step 1 except the upper
blower motor retaining screw.
Blower
Retaining Screw
Blower
Shield
Blower
Retaining Screw
Back of
Microwave Oven
8
.
Slide the exhaust adaptor onto the back of
the microwave oven, securing it into the lower
locking tabs. Take care to ensure that the
damper hinge is installed so that it is at the top
and that the damper swings freely. Reinstall the
upper blower motor screw through the adaptor
and the blower door and into the back of the
microwave oven.
Guide
Guide
Adaptor
Locking Tabs
(not shown)
Blower Motor Door
Retaining Screw
Back of
Microwave Oven
ME4000R_ME17R7021EB_AA_DE68-04584A-00_EN.indd
14
6/19/2019
4:17:43 PM