Samsung PN50C430A1D Quick Guide (easy Manual) (ver.1.0) (English) - Page 1

Quick Setup Guide Congratulations on the purchase of your new Samsung TV. Read this setup guide to get your TV up and running quickly. STOP Please do not return this unit. If you have problems operating your TV, call: 1-800-SAMSUNG (1-800-726-7864) For web support please visit: www.samsung.com/support 1-800-SAMSUNG (1-800-726-7864) Samsung Electronics America, Inc. 85 Challenger Road Ridgefield Park, NJ 07660-2112 Samsung Electronics Canada Inc. 55 Standish Court Mississauga, Ontario L5R 4B2 Call Center hours of operation: Mon-Sun, 9:00 AM -12 AM EST. To register this product, visit: www.samsung.com/ register. Step 1: Install the Stand Follow the steps below to connect the TV to the stand. ✎✎NOTE xx Make sure to distinguish between the front and back of the Stand and Guide Stand when assembling them. xx Make sure that at least two persons lift and move the PDP TV. xx Stand the product up and fasten the screws. If you fasten the screws with the PDP TV placed down, it may lean to one side. 1 2 With your TV upright, connect the Fasten the two screws (M4 X L16) TV to the Stand as shown. at position 1, and then fasten the two screws (M4 X L16) at position 2. Rear s s s s Front s s s s 2 1 Step 4: Connect External Devices Connecting an AV device (DVD/ Blu-ray player, cable/satellite box, etc.) Use one of the connections below to connect your TV to an external A/V device. We recommend using HDMI for the highest picture quality. HDMI to DVI Cable (Not Supplied) Very Good Connection HD connection (up to 720p/1080i) Using a HDMI to DVI Cable Device AUDIO OUT DVI OUT Audio Cable (Not Supplied) Good Connection Component connection (up to 720p/1080i) Using a Component Cable DVD / Blu-ray player / HD Cable Box / HD Satellite receiver (STB) Device COMPONENT OUT AUDIO OUT Audio Cable (Not Supplied) Component Cable (Not Supplied) HDMI Cable (Not Supplied) Best Connection HD connection (up to 720p/1080i) Using an HDMI Cable DVD / Blu-ray player / HD Cable Box / HD STB (Set-Top-Box) satellite receiver HDMI OUT Device Audio Cable (Not Supplied) Video Cable (Not Supplied) Lowest Quality Connection Audio/Video connection (480i only) Using an Audio/Video Cable DVD, Blu-ray player, cable box, STB satellite receiver, VCR VIDEO OUT AUDIO OUT Device ✎✎When connecting to AV IN on the back of your TV, attach the video cable (yellow) to the green jack next to the AV IN label. The jack will not match the color of the video cable (yellow). Connecting an audio device (Home Theater, etc.) Connect your TV to your Home Theater or other audio device to enjoy enhanced Sound quality. Audio Cable (Not Supplied) Analog Audio connection Using an Audio Cable Amplifier / DVD Home Theater AUDIO IN Optical Cable (Not Supplied) Digital Audio connection Using an Optical Cable Digital Audio System OPTICAL Connecting a PC Connect your TV to a PC to use it as a Monitor. Audio Cable (Not Supplied) HDMI to DVI Cable (Not Supplied) HD connection Using a HDMI to DVI Cable AUDIO OUT DVI OUT Step 2: Install the Batteries into the Remote To install batteries into your remote control, follow these steps: 1. Lift the cover on the back of the remote upward as shown in the figure to the right. 2. Install two AAA batteries. ✎✎ Make sure to match the + and - ends of the batteries to the diagram in the battery compartment. 3. Replace the cover. Step 3: Connect Power and Antenna or Cable VHF/UHF Antenna Connect Ant In to or Best to use 75 ohm (round) cable. • Wall cable jack • VHF/UHF Antenna • Cable or Satellite box Ant or Cable Out Make sure the AC power cord is plugged in securely to the wall outlet and the TV. Antenna Cable (Not Supplied) Step 5: Run Plug & Play When you turn on your TV for the first time, it automatically launches the Plug & Play function. With Plug & Play, you can select the On Screen Display language, set the clock mode, and launch the TV's channel memorizing process. It also displays connection instructions similar to those in this guide. To navigate while Plug & Play is running, press the Up, Down, Left or Right arrow buttons on your remote. To make a selection, press the ENTERE button. To skip a screen, press the MENU button. To turn on your TV, press the POWER button on the remote or on the TV. To run Plug & Play, follow these steps: 1 Using your remote control, select the language for the On Screen Display (OSD), and then press the ENTERE button. Plug & Play Plug & Play Select Language of the OSD. Language English Español Français U Move E Enter 2 Select Home Use, and then press the ENTERE button. If you select Store Demo, the TV will reset your picture and audio settings every 30 minutes. Plug & Play Select 'Home Use' when installing this TV in your home. Store Demo Home Use L Move E Enter 3 Select the Antenna Source to memorize. you must select Antenna Source to same type as your cable system type. After selecting source, select Start; then press the ENTERE button on your remote. Plug & Play Select the Antenna source to memorize. Air Cable Auto Start Start Start U Move E Enter m Skip ✎✎Most cable systems are Standard(STD) systems, If you are not sure about what kind of cable system you have, contact your cable company. ✎✎If your TV is attached to a cable or satellite box, skip Steps 3 through 5. After Plug & Play is complete, set your TV to Channel 3 or 4, according to the directions for your cable or satellite box. 4 The TV memorizes the available channels. This process can take up to 45 minutes. 5 After the TV has memorized the channels, choose the Clock Mode. Select Auto if you have a digital channel in your area. Select Manual if you don't, or if you have a cable or satellite box. When done, press the ENTERE button. ✎✎ If you select Manual, the clock setting screen appears. 6 Select the daylight savings time setting: Off, On or Auto and then press the ENTERE button. Plug & Play Auto Program in Progress. DTV Air : -- Air : -- DTV Cable : -- Cable : -- Cable : 35 48% Stop E Enter m Skip Plug & Play Set the Clock Mode. Clock Mode Auto Manual U Move E Enter m Skip Plug & Play Set to daylight saving time. Auto DST On Auto U Move E Enter m Skip 7 Select the time zone in which you live, and then press ENTERE. 8 After the time zone screen, The connection method for best HD screen quality is displayed. Press Right arrow button on your remote to view each screen in succession. Press the Blue button to skip this section. 9 The Enjoy your TV. screen appears. Then press the ENTERE button. If You Want to Rerun Plug & Play 1. Press the SOURCE button on your remote, then select TV mode. 2. Press the MENU button on your remote to display the menu. 3. Press the ▲ or ▼ button to select Setup, and then press the ENTERE button. 4. Press ENTERE again to select Plug & Play. BN68-02608A-02