Samsung PN63C590G4F Quick Guide (easy Manual) (ver.1.0) (English) - Page 1

Quick Setup Guide Congratulations on the purchase of your new Samsung TV. Read this setup guide to get your TV up and running quickly. STOP Please do not return this unit. If you have problems operating your TV, call: 1-800-SAMSUNG (1-800-726-7864) For web support please visit: www.samsung.com/support 1-800-SAMSUNG (1-800-726-7864) Samsung Electronics America, Inc. 85 Challenger Road Ridgefield Park, NJ 07660-2112 Samsung Electronics Canada Inc. 55 Standish Court Mississauga, Ontario L5R 4B2 Call Center hours of operation: Mon-Sun, 9:00 AM -12 AM EST. To register this product, visit: www.samsung.com/ register. Step 1: Install the Stand 50 inches model only Follow the steps below to connect the TV to the stand. ✎✎NOTE xx Make sure to distinguish between the front and back of the Stand and Guide Stand when assembling them. xx Make sure that at least two persons lift and move the PDP TV. xx Stand the product up fasten the screws. If you fasten the screws with the with the PDD TV placed down, it may lean to one side. Screws (M4 X L12) Top view Guide Stand 1 Connect the Guide Stand to the Stand using five screws (M4 X L1St2an)d Front as shown. 2 3 With your TV upright, connect the Rear Rear Fasten two screws (M4 X L12) at TV to the Stand as shown. position 1, and then fasten the two screws (M4 X L2) at position 2. 2 1 Step 2:ReIanr stall the Batteries into the Remote To install batteries into your remote control, follow these steps: 1. Lift the cover on the back of the remote upward as shown in the figure to the right. 2. Install two AAA batteries. ✎✎ Make sure to match the + and - ends of the batteries to the diagram in the battery compartment. 3. Replace the cover. Step 3: Connect Power and Antenna or Cable VHF/UHF Antenna Connect Ant In to or Use a 75 ohm (round) cable. • Wall cable jack • VHF/UHF Antenna • Cable or Satellite box Ant or Cable Out Make sure the AC power cord is plugged in securely to the wall outlet and the TV. Step 4: Connect External Devices Connecting an AV device (DVD/Blu-ray player, cable/satellite box, etc.) Use one of the connections below to connect your TV to an external A/V device. We recommend using HDMI for the highest picture quality. HDMI to DVI Cable (Not Supplied) HDMI Cable (Not Supplied) Audio Cable (Not Supplied) Best Connection HD connection (up to 1080p) Very Good Connection HD connection (up to 1080p) Using an HDMI to DVI Cable Using an HDMI Cable DVD / Blu-ray player / HD Cable Box / HD STB (Set-Top-Box) satellite receiver HDMI OUT DVD Connecting an audio device (Home Theater, etc.) Connect your TV to your Home Theater or other audio device to enjoy enhanced Sound quality. Analog Audio connection Using an Audio Cable Audio Cable (Not Supplied) AUDIO IN Amplifier / DVD home theater Optical Cable (Not Supplied) Digital Audio connection Using an Optical Cable Digital Audio System OPTICAL Device AUDIO OUT DVI OUT Good Connection Component connection (up to 1080p) Using an Audio/Video Cable DVD / Blu-ray player / HD Cable Box / HD Satellite receiver (STB) Blu-ray player COMPONENT OUT AUDIO OUT Component Cable (Not Supplied) Audio Cable (Not Supplied) Step 5: Run Plug & Play When you turn on your TV for the first time, it automatically launches the Plug & Play function. With Plug & Play, you can select the On Screen Display language, set the clock mode, and launch the TV's channel memorizing process. It also displays connection instructions similar to those in this guide. To navigate while Plug & Play is running, press the Up, Down, Left or Right arrow buttons on your remote. To make a selection, press the ENTERE button. To skip a screen, press the MENU button. To turn on your TV, press the POWER button on the remote or on the TV. To run Plug & Play, follow these steps: 1 Using your remote control, select the language for the On Screen Display (OSD), and then press the ENTERE button. Plug & Play Select Language of the OSD. Menu Language : English Español Français 2 Select Home Use, and then U Move E Enter press the ENTERE button. If you select Store Demo, the TV will reset your picture and audio settings every 30 minutes. 3 Select Antenna Source and Channel Source. If Antenna Source is Cable or Auto, you must select Channel Source to same type as your cable system type. After selecting source, select Search; then press the ENTERE button on your remote. ✎✎ Most cable systems are Standard(STD) systems, If you are not sure about what kind of cable system you have, contact your cable company. ✎✎ If your TV is attached to a cable or satellite box, skip Steps 3 through 5. After Plug & Play is complete, set your TV to Channel 3 or 4, according to the directions for your cable or satellite box. 4 The TV memorizes the available channels. This process can take up to 45 minutes. 5 After the TV has memorized the channels, choose the Clock Mode. Select Auto if you have a digital channel in your area. Select Manual if you don't, or if you have a cable or satellite box. When done, press the ENTERE button. ✎✎ If you select Manual, the clock setting screen appears. Video Cable (Not Supplied) Audio Cable (Not Supplied) Lowest Quality Connection Audio/Video connection (480i only) Using a Component Cable AUDIO OUT DVD, Blu-ray player, cable box, STB satellite receiver, VCR VIDEO OUT Device ✎✎When connecting to AV IN 1 on the back of your TV, attach the video cable (yellow) to the green jack next to the AV IN 1 label. The jack will not match the color of the video cable (yellow). 6 Select the daylight savings time setting: Off or On, and then press the ENTERE button 7 Select the time zone in which you live, and then press ENTERE button. 8 After the time zone screen, The connection method for best HD screen quality is displayed. Press Right arrow button on your remote to view each screen in succession. Press the Blue button to skip this section. 9 The Enjoy your TV. screen appears. Then press the ENTERE button. Changing the Screen Size Your TV has several screen size options, each designed to work best with specific types of video input. If you have a cable box or satellite receiver, it may have its own set of screen sizes as well. To change the screen size, press the P.SIZE button on your remote. The first time you press it, your TV displays the current setting. Thereafter, each time you press the P.SIZE button, you change the size of the picture on the screen. The following sizes are available: 16:9 Wide screen 4:3 Standard screen Wide Fit Zoom 1 Zoom 2 Screen Fit ✎✎Screen Fit Displays the full image without any cut-off when HDMI (720p / 1080i / 1080p) or Component (1080i / 1080p) signals are inputted. Connecting a PC Connect your TV to a PC to use it as a Monitor. Audio Cable (Not Supplied) HDMI to DVI Cable (Not Supplied) HD connection Using a DVI to HDMI Cable AUDIO OUT DVI OUT Using an D-Sub Cable D-Sub Cable (Not Supplied) Audio Cable (Not Supplied) Changing the Picture Mode PC OUT AUDIO OUT Your TV has three preset Picture Modes with factory adjusted settings, each designed to give you an excellent picture under specific conditions. To change the Picture mode, press the P.MODE button on your remote. The first time you press it, your TV displays the current setting. Thereafter, each time you press the P.MODE button, you change the mode of the picture on the screen. The Picture Modes are listed and described in the table below: Mode Dynamic Standard Movie Description Brightens picture. For a vibrant, enhanced image in brightly lit or sunny room. For a bright, detailed picture in a normally lit room. For a studio quality cinema picture in a dimly lit or dark room. To change the Picture Mode, follow these steps: 1. Turn on your TV, press the TOOLS button on your remote. The Tools menu appears. 2. Using the ▲ or ▼ on your remote, select Picture mode. 3. On the Picture mode menu, use the ◄ or ► on your remote to select the Picture mode you want. 4. Press the EXIT button to exit the menu. Setting the Clock Before you can use your TV's On/Off Timer, you must set the clock. To set the clock, follow these steps: 1. Turn on your TV, press the MENU button on your remote, then select Setup → Time. 2. Select Clock Mode, and then press the ENTERE button. 3. Choose Auto or Manual. xx If you select Auto, the current time will be set automatically using the time from a digital channel. xx If you select Manual, you can set the Month, Day, Year, Hour, Minute and am/pm directly by pressing up, down, left and right arrow button on your remote. 4. Press the RETURN button on your remote when done.