Samsung RF261BEAESG User Manual - Page 7

Required Tools, Removing The Refrigerator, Doors

Get Samsung RF261BEAESG PDF manuals and user guides View all Samsung RF261BEAESG manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

01 setting up FLOORING For proper installation, you must place this refrigerator on a level, hard surface that is the same height as the rest of the floor. This surface should be strong enough to support a fully loaded refrigerator, or approximately 335lbs (152kg). To protect the finish of the flooring, cut a large section of the cardboard carton and place it under the refrigerator where you are working. When moving the refrigerator, you need to pull and push it straight forwards or back. Do not wiggle it from side to side. REMOVING THE REFRIGERATOR DOORS For some installations you need to remove the fridge and freezer drawers so you can move the refrigerator to its final location. Do not remove the doors/drawer if you don't need to. If you do not need to remove the refrigerator doors, go to Adjusting the Level on page 10. If you need to remove the doors. continue below. Before removing the door/drawer, make sure you read the following items: Disconnect power to the refrigerator WARNING before removing the door or drawer. REQUIRED TOOLS • Be careful not to drop, damage or scratch the door/drawer while removing them. • Use care when you remove the doors/drawer. The doors are heavy and you could injure yourself. • Reattach the doors/drawer properly to avoid: - Moisture from air leakage. - Uneven door alignment. - Wasting energy due to improper door seal. Required Tools (Not provided) You need the following tools to complete the installation of your refrigerator: Philips Flat-blade screw Socket wrench screwdriver(+) driver(-) (10mm) HOW TO ASSEMBLE THE HANDLE Orient each handle so that the end with the sticker attached is at the top and the holes with the tightening screws are facing each other. Then, follow the directions below to install each handle. Allen wrench (3/16") (5mm) DA68-02601B-14.indb 7 By using Phillips screwdriver, fix the screw (optional) and then put the handle on the fixer by sliding them down firmly. setting up _7 2018. 10. 8. 오후 5:04

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
setting up
_7
01
SETTING UP
FLOORING
For proper installation, you must place this
refrigerator on a level, hard surface that is the
same height as the rest of the floor. This surface
should be strong enough to support a fully loaded
refrigerator, or approximately 335lbs (152kg).
To protect the finish of the flooring, cut a large
section of the cardboard carton and place it under
the refrigerator where you are working. When
moving the refrigerator, you need to pull and push
it straight forwards or back. Do not wiggle it from
side to side.
REQUIRED TOOLS
Required Tools (Not provided)
You need the following tools to complete the
installation of your refrigerator:
Philips
screwdriver(+)
Flat-blade screw
driver(-)
Socket wrench
(10mm)
Allen wrench
(3/16”) (5mm)
REMOVING THE REFRIGERATOR
DOORS
For some installations you need to remove the
fridge and freezer drawers so you can move the
refrigerator to its final location.
Do not remove
the doors/drawer if you don’t need to.
If you
do not need to remove the refrigerator doors, go
to Adjusting the Level on page 10. If you need to
remove the doors. continue below.
Before removing the door/drawer, make sure you
read the following items:
Disconnect power to the refrigerator
before removing the door or drawer.
• Be careful not to drop, damage or
scratch the door/drawer while removing
them.
•
Use care when you remove the doors/drawer.
The doors are heavy and you could injure
yourself.
•
Reattach the doors/drawer properly to avoid:
-
Moisture from air leakage.
-
Uneven door alignment.
-
Wasting energy due to improper door seal.
HOW TO ASSEMBLE THE HANDLE
Orient each handle so that the end with the sticker
attached is at the top and the holes with the
tightening screws are facing each other.
Then, follow the directions below to install each
handle.
By using Phillips screwdriver, fix the screw
(optional) and then put the handle on the fixer by
sliding them down firmly.
WARNING
DA68-02601B-14.indb
7
2018. 10. 8.
오후 5:04