Samsung RF32FMQDBSR User Manual Ver.0.1 (English, French, Spanish) - Page 14

Installing The Water, Dispenser Line - water filter

Get Samsung RF32FMQDBSR PDF manuals and user guides View all Samsung RF32FMQDBSR manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

HOW TO ADJUST THE DOOR GAP If the gap between the left and right fridge compartment doors is not even. • You can adjust the gap by turning the bolt at the top right of the cold storage compartment door. • Do not turn the bolt too far. You can break it. • Water line installation kits are available at extra cost from your dealer. We recommend using a water line installation kit that contains copper tubing and ¼" compression nut. Connecting to the water supply line 1. First, shut off the main water supply. 1. With the doors closed, remove the 3 screws holding the top cover using a Phillips screwdriver, and then lift it off together with the connected cables. 2. Locate the nearest cold water drinking line and install the pipe clamp and shut off valve. Cold water line Pipe clamp Shut off valve 2. Turn the bolt with a 4 mm hexagonal L-wrench to adjust the gap. (Not provided) 3. Connect the water line installation kit to the shut off valve. 3. Turn the bolt clockwise to ( ) widen the gap. Turn the bolt counter clockwise ( the gap. ) to narrow INSTALLING THE WATER DISPENSER LINE Cold water line Pipe clamp Shut off valve Water line installation kit A water dispenser with a filter is one of the helpful features on your new refrigerator. To help promote better health, the water filter removes unwanted particles from your water. However, it does not sterilize or destroy microorganisms. You may need to purchase a water purifying system to do that. The water line also connects to the ice maker. For the ice maker to operate properly, water pressure of 20~125 psi (138~862 kPa) is required. If the refrigerator is installed in an area with low water pressure (below 20 psi), you can install a booster pump to compensate for the low pressure. After you have connected the water line, make sure the water storage tank inside the refrigerator is properly filled. To do this, press the water dispenser lever until the water runs from the water outlet. Connecting the water supply line to the refrigerator. There are several items that you need to purchase to complete this connection. You may find these items sold as a kit at your local hardware store. For Copper Tubing For Plastic Tubing • ¼" copper tubing • ¼" plastic tubing • ¼" compression nut (1pc) → Molded end(Bulb) • Ferrule (2pc) • ¼" compression nut (1pc) 14_ setting up DA68-02918A-01.indb 14 13. 4. 25. �� 2:30

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
14_
setting up
HOW TO ADJUST THE DOOR GAP
If the gap between the left and right fridge
compartment doors is not even.
•
You can adjust the gap by turning
the bolt at the top right of the cold
storage compartment door.
•
Do not turn the bolt too far.
You can break it.
1.
With the doors closed, remove the 3 screws
holding the top cover using a Phillips
screwdriver, and then lift it off together with the
connected cables.
2.
Turn the bolt with a 4 mm
hexagonal L-wrench to adjust
the gap. (Not provided)
3.
Turn the bolt clockwise to
(
) widen the gap.
Turn the bolt counter clockwise (
) to narrow
the gap.
INSTALLING THE WATER
DISPENSER LINE
A water dispenser with a filter is one of the helpful
features on your new refrigerator. To help promote
better health, the water filter removes unwanted
particles from your water. However, it does not
sterilize or destroy microorganisms. You may need
to purchase a water purifying system to do that.
The water line also connects to the ice maker.
For the ice maker to operate properly, water
pressure of 20~125 psi (138~862 kPa) is required.
If the refrigerator is installed in an area with low
water pressure (below 20 psi), you can install a
booster pump to compensate for the low pressure.
After you have connected the water line, make
sure the water storage tank inside the refrigerator is
properly filled. To do this, press the water dispenser
lever until the water runs from the water outlet.
• Water line installation kits are available at
extra cost from your dealer.
We recommend using a water line
installation kit that contains copper
tubing and ¼” compression nut.
Connecting to the water supply line
1.
First, shut off the main water
supply.
2.
Locate the nearest cold water drinking line and
install the pipe clamp and shut off valve.
Pipe clamp
Cold water line
Shut off valve
3.
Connect the water line installation kit to the shut
off valve.
Shut off valve
Pipe clamp
Cold water line
Water line installation kit
Connecting the water supply line to the
refrigerator.
There are several items that you need to purchase
to complete this connection.
You may find these items sold as a kit at your local
hardware store.
For Copper Tubing
For Plastic Tubing
• ¼” copper tubing
• ¼” compression nut (1pc)
• Ferrule (2pc)
• ¼” plastic tubing
→
Molded end(Bulb)
• ¼” compression nut (1pc)
DA68-02918A-01.indb
14
13. 4. 25.
�� 2:30