Samsung RF4267HARS User Manual (user Manual) (ver.0.2) (English, French, Spani - Page 9

ADJUSTING THE FREEZER DRAWER, LEVEL, The thickness of each fastener is 0.04. - refrigerator

Get Samsung RF4267HARS PDF manuals and user guides
UPC - 036725560673
View all Samsung RF4267HARS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

Fixed part Adjustment part Adjusting the freezer drawer level Adjustment part 01 setting up The left door is fixed. To make minor adjustments between doors, adjust only the right door. 1. Pull out the Convertible door ( 1 ) to expose the lower hinge ( 2 ). 2. Insert the supplied allen wrench (3/16") ( 3 ) into the shaft ( 4 ) of the lower hinge. 3. Please adjust the height by turning the hex wrench ( 3 ) clockwise ( DOWN ) or counter- clockwise ( UP ). When you turn the hex wrench counterclockwise ( ), the door will move up. 2 3 3 4 1 Freezer Drawer 1. Locate the height-adjuster ( 1 ) in the freezer drawer. Unscrew the 8 Phillips screws ( 2 ) slightly to loosen the door. 1 2 2. Loosen the controller screw ( 3 ) with a Phillips screwdriver (+). 3 1. After adjusting the doors, insert the supplied fastener ( 6 ) using a pliers ( 5 ) in the gap between the hinge-grommet ( 7 ) and the lower hinge ( 8 ). The number of fasteners you'll need to insert depends on the gap. 3. Find the best level to align the door slope. • After adjustment, tighten the controller screw ( 3 ) and then philips screws. Example) The slope is about 0.08inch (2mm) as shown below. - Rotate the height adjuster to -2.0 to reduce the door slope. 2 fastener are enclosed with the refrigerator. The thickness of each fastener is 0.04". Slope Reference plane setting up _09

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
setting up
_09
01 SETTING UP
The left door is fixed. To make minor
adjustments between doors, adjust only the
right door.
1.
Pull out the Convertible door (
1
) to expose the
lower hinge (
2
).
2.
Insert the supplied allen wrench (3/16”) (
3
) into
the shaft (
4
) of the lower hinge.
3.
Please adjust the height by turning the hex
wrench (
3
) clockwise (
DOWN
) or counter-
clockwise (
UP
).
When you turn the hex wrench counter-
clockwise (
), the door will move up.
1.
After adjusting the doors, insert the supplied
fastener (
6
) using a pliers (
5
) in the gap
between the hinge-grommet (
7
) and the lower
hinge (
8
). The number of fasteners you’ll need to
insert depends on the gap.
2 fastener are enclosed with the refrigerator.
The thickness of each fastener is 0.04”.
ADJUSTING THE FREEZER DRAWER
LEVEL
1.
Locate the height-adjuster (
1
) in the freezer
drawer.
Unscrew the 8 Phillips screws (
2
) slightly to
loosen the door.
2.
Loosen the controller
screw (
3
) with a Phillips
screwdriver (+).
3.
Find the best level
to align the door
slope.
•
After
adjustment,
tighten the
controller screw
(
3
) and then
philips screws.
3
1
2
3
4
Freezer Drawer
Adjustment part
1
2
3
Example) The slope is about 0.08inch (2mm) as shown below.
- Rotate the height adjuster to -2.0 to reduce the door slope.
Slope
Reference
plane
Adjustment
part
Fixed part