Samsung RFG297AARS/XAA User Manual (user Manual) (ver.1.0) (English) - Page 20

Reverse Osmosis Water Supply, Removing any residual matter inside the water supply line - leaking water inside refrigerator

Get Samsung RFG297AARS/XAA PDF manuals and user guides View all Samsung RFG297AARS/XAA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

Setting up your French Door Refrigerator 4. R emove the filter cap and insert the filter into the filter housing. 5. Slowly turn the water filter 90º clockwise to align with the printing mark on the cover, locking the filter in position. Make sure to align the water filter label mark with center of cover filter printing as illustrated. Remember, do not over-tighten. 4 Separation of red cap. Cover filter. 5 Turn until the label is aligned. You should remove the right side upper glass shelf before installing the water filter. Removing any residual matter inside the water supply line after installing the water filter. 1. T urn ON the main water supply & turn OFF the valve to the water supply line. 2. R un water through the dispenser until the water runs clear (approx. 6-7minutes). This will clean the water supply system and remove air from the lines. 3. Additional flushing may be required in some households. 4. O pen the Refrigerator door and make sure there are no water leaks coming from the water filter. Be sure to flush the dispenser thoroughly or water may from it. This is due to the fact that there is still air in the line. Reverse Osmosis Water Supply IMPORTANT : The pressure of the water supply coming out of a reverse osmosis system going to the water inlet valve of the refrigerator needs to be between 35 and 120 psi (241 and 827 kPa). If a reverse osmosis water filtration system is connected to your cold water supply, the water pressure to the reverse osmosis system needs to be a minimum of 40 to 60 psi (276 to 414 kPa.) If the water pressure to the reverse osmosis system is less than 40 to 60 psi (276 to 414 kPa): • C heck to see whether the sediment filter in the reverse osmosis system is blocked. Replace the filter if necessary. • Allow the storage tank on the reverse osmosis system to refill after heavy usage. • If your refrigerator has a water filter, it may further reduce the water pressure when used in conjunction with a reverse osmosis system. Remove the water filter. If you have questions about your water pressure, call a licensed, qualified plumber. 20_ Setting Up

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
20_
Setting Up
You should remove the right side upper glass shelf before installing the water filter.
Reverse Osmosis Water Supply
IMPORTANT :
The pressure of the water supply coming out of a reverse osmosis
system going to the
water inlet valve of the
refrigerator needs to be between 35 and 120 psi (241 and 827 kPa).
If a reverse osmosis water filtration system is
connected to your cold water supply, the water pressure to
the reverse osmosis
system needs to be a minimum of 40 to 60 psi (276 to 414 kPa.)
If the water pressure to the reverse osmosis system is less than 40 to 60 psi (276 to 414 kPa):
•
Check to see whether the sediment filter in the reverse osmosis system is blocked. Replace the filter if
necessary.
•
Allow the storage tank on the reverse osmosis system to refill after heavy usage.
•
If your refrigerator has a water filter, it may further reduce the water pressure when used in conjunction
with a reverse osmosis system. Remove the water filter.
If you have questions about your water
pressure, call a licensed, qualified plumber.
Setting up your French Door Refrigerator
Turn until the label
is aligned.
Separation
of red cap.
Cover filter.
4
5
Removing any residual matter inside the water supply line
after installing the water filter.
1.
Turn ON the main water supply & turn OFF the valve to the water supply
line.
2.
Run water through the dispenser until the water runs clear (approx.
6-7minutes). This will clean the water supply system and remove air
from the lines.
3.
Additional flushing may be required in some households.
4.
Open the Refrigerator door and make sure there are no water leaks
coming from the water filter.
Be sure to flush the dispenser thoroughly or water may from it.
This is due to the fact that there is still air in the line.
4.
Remove the filter cap and insert the filter into the filter
housing.
5. Slowly turn the water filter 90º clockwise to align
with the printing mark on the cover, locking the filter
in position. Make sure to align the water filter label
mark with center of cover filter printing as illustrated.
Remember, do not over-tighten.