Samsung SCX-4623FW Quick Guide (easy Manual) (ver.1.0) (English) - Page 36
Setting IP address, IP setting using control panel, IP setting using SetIP Program Windows - driver mac
UPC - 635753615197
View all Samsung SCX-4623FW manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 36 highlights
• MAC Address:00:15:99:41:A2:78 • IP Address:192.0.0.192 Setting IP address First, you have to set up an IP address for network printing and managements. In most cases a new IP address will be automatically assigned by a DHCP (Dynamic Host Configuration Protocol) server located on the network. In a few situations the IP address must be set manually. This is called a static IP and is often required in corporate Intranets for security reasons. • DHCP IP assignment: Connect your machine to the network, and wait a few minutes for the DHCP server to assign an IP address to the machine. Then, print the Network Configuration Report as explained above. If the report shows that the IP address has changed, the assignment was successful. You will see the new IP address in the report. • Static IP assignment: Use SetIP program to change the IP address from your computer. If your machine has a control panel, you can also change IP address using the machine's control panel. In an office environment, we recommend that you contact a network administrator to set this address for you. IP setting using control panel 1. Connect your machine to the network with a network cable. 2. Turn on the machine. 3. Press Menu on the control panel. 4. Press the left/right arrow until Network appears and press OK. 5. Press the left/right arrow until TCP/IP (IPv4) appears and press OK. 6. Press the left/right arrow until Static appears and press OK. 7. Press the left/right arrow until IP Address appears and press OK. 8. Enter the IP address using numeric keypad and press OK. Enter a byte between 0 and 255 using the number keypad and press the left/right arrow to move between bytes. Repeat this to complete the address from the 1st byte to the 4th byte. 9. Enter other parameters, such as the Subnet Mask and Gateway appears and press OK. 10. After entering all parameters, press Stop/Clear to return to ready mode. Now go to "Installing wired network or USB connected machine's driver" on page 37. IP setting using SetIP Program (Windows) This program is for manually setting the network IP address of your machine using its MAC address to communicate with the machine. A MAC address is the hardware serial number of the network interface and can be found in the Network Configuration Report. For using SetIP program, disable the computer firewall before continuing by performing the following: 1. Open Control Panel. 2. Double click Security Center. 3. Click Windows Firewall. 4. Disable the firewall. Installing the program 1. Insert the Printer Software CD-ROM provided with your machine. When the driver CD runs automatically, close that window. 2. Start Windows Explorer and open the X drive (X represents your CD-ROM drive). 3. Double-click Application > SetIP. 4. Double-click Setup.exe to install this program. 5. Select a language, then click Next. 6. Follow the instructions in the window and complete the installation. Starting the program 1. Connect your machine to the network with a network cable. 2. Turn on the machine. 3. From the Windows Start menu, select All Programs > Samsung Printers > SetIP > SetIP. 4. Click on the icon (third from left) in the SetIP window to open the TCP/IP configuration window. 5. Enter the machine's new information into the configuration window as follows. In a corporate intranet, you may need to have this information assigned by a network manager before proceeding. • MAC Address: Find the machine's MAC address from the Network Configuration Report and enter it without the colons. For example, 00:15:99:29:51:A8 becomes 0015992951A8. • IP Address: Enter a new IP address for your printer. For example, if your computer's IP address is 192.168.1.150, enter 192.168.1.X (X is number between 1 and 254 other than the computer's address). • Subnet Mask: Enter a Subnet Mask. • Default Gateway: Enter a Default Gateway. 6. Click Apply, and then click OK. The machine will automatically print the Network Configuration Report. Confirm that all the settings are correct. 7. Click Exit to close the SetIP program. 8. If necessary, restart the computer's firewall. IP setting using SetIP Program (Macintosh) For using SetIP program, disable the computer firewall before continuing by performing the following: 1. Open System Preferences. 2. Click Security. 3. Click the Firewall menu. 4. Turn firewall off. Network setup_ 36