Samsung SPH710AE User Manual (ENGLISH) - Page 9

Indicator Information, Clearing Indicator Problems - projector

Get Samsung SPH710AE - 700 Lumens XGA DLP Projector PDF manuals and user guides
UPC - 770332709192
View all Samsung SPH710AE manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

Preparation Projector and Accessories Indicator Information : Turned On : Flashing : Turned Off TEMP LAMP STANDBY Information If you press the POWER button on the remote control or projector, the screen appears within 30 seconds. The projector is in normal operating condition. The projector is warming up after POWER button has been pressed. The POWER button is pressed to turn off the projector, and the cooling system is in operation to cool off inside of the projector. (Lasts for about 1 minute and 30 seconds) Refer to measure 1 below if the cooling fan inside the projector is not in normal operation condition. Refer to measure 2 below if the lamp cover protecting the lamp unit is not closed properly. Power is turned off automatically when temperature inside of the projector goes beyond the control limit. Refer to measure 3. Refer to measure 4 below if the life span of the lamp is running out or a problem with the lamp is detected. Clearing Indicator Problems Classification Measure 1 Measure 2 Measure 3 Measure 4 State Measures When the cooling fan system is Unplug and plug the cord and restart the projector. If the not in normal operating condition. problem does not disappear, contact a dealer or service personnel near you. When the lamp cover protecting the lamp unit is not properly closed or the sensor system is not in normal operating condition. Check the screw on the bottom side of the projector. If you do not find any problem, contact a dealer or service personnel near you. When temperature inside of the projector becomes too high. Adjust the position of the projector following the installation instructions of this manual and cool off the projector before restarting it. If the problem does not disappear, contact a dealer or service personnel near you. The lamp is malfunctioning after Power off the projector and cool it off for some time before abnormal power off or restarting restarting it. right after turning off the projector. When brightness of the picture screen degrades or image deterioration is found. Check how long the lamp has been used on Information and contact a dealer or service personnel near you for lamp replacement. This Projector uses a cooling fan system to keep the unit from overheating. NOTE Operation of the cooling fan may cause noise, which does not affect the product performance. No exchange or refund for the noise concern. 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
Preparation
Projector and Accessories
9
: Turned On
: Flashing
: Turned Off
STANDBY
LAMP
TEMP
Information
If you press the
POWER
button on the remote control or projector, the screen
appears within 30 seconds.
The projector is in normal operating condition.
The projector is warming up after
POWER
button has been pressed.
The
POWER
button is pressed to turn off the projector, and the cooling system is
in operation to cool off inside of the projector. (Lasts for about 1 minute and 30
seconds)
Refer to measure 1 below if the cooling fan inside the projector is not in normal
operation condition.
Refer to measure 2 below if the lamp cover protecting the lamp unit is not closed
properly.
Power is turned off automatically when temperature inside of the projector goes
beyond the control limit. Refer to measure 3.
Refer to measure 4 below if the life span of the lamp is running out or a problem
with the lamp is detected.
When the cooling fan system is
not in normal operating condition.
When the lamp cover protecting
the lamp unit is not properly
closed or the sensor system is not
in normal operating condition.
When temperature inside of the
projector becomes too high.
The lamp is malfunctioning after
abnormal power off or restarting
right after turning off the projector.
When brightness of the picture
screen degrades or image
deterioration is found.
Unplug and plug the cord and restart the projector. If the
problem does not disappear, contact a dealer or service
personnel near you.
Check the screw on the bottom side of the projector. If you
do not find any problem, contact a dealer or service
personnel near you.
Adjust the position of the projector following the
installation instructions of this manual and cool off the
projector before restarting it. If the problem does not
disappear, contact a dealer or service personnel near you.
Power off the projector and cool it off for some time before
restarting it.
Check how long the lamp has been used on Information
and contact a dealer or service personnel near you for lamp
replacement.
Measure 1
Measure 2
Measure 3
Measure 4
Indicator Information
Classification
State
Measures
Clearing Indicator Problems
NOTE
This Projector uses a cooling fan system to keep the unit from overheating.
Operation of the cooling fan may cause noise, which does not affect the product performance.
No exchange or refund for the noise concern.