Samsung SRP-500C Installation Guide - Page 1

Printer Installation Guide KN06-00002A (Rev.1.0) INKJET PRINTER SRP-500 ◈ Information This Installation Guide includes a brief outline of information necessary for product installation. For more detailed installation information, please refer to the user manual in the enclosed CD. The contents of the CD include the following. 1. Manual: User Manual, Code Chart, Control Commands 2. Drivers: Windows Drivers, OPOS Drivers 3. Utilities: a logo download tool ◈ Installing the Paper Roll 1. Open the rear cover. 2. Insert a new paper roll, making sure to align it properly. 3. Pull out a small amount of paper, and close the rear cover. ◈ Components Cable Cover Paper Roll Ink Cartridge Procuct Installation CD CD SRP-500 AC/DC Adaptor Power cord Installation Guide ◈ Connecting the cables 1. Plug the power cord into the AC Adaptor, and then plug the AC Adaptor into the power connector of the printer 2. Turn off the printer and the host ECR (host computer). 3. Check the interface cable (Serial, Parallel, USB), and connect the interface connector cable accordingly. 4. Plug the drawer kick-out cable into the drawer kick-out connector on the printer. Drawer kick-out connector Power connector Interface connector Interface cable (Serial/Parallel/USB) Adaptor Drawer kickout cable Power cord ◈ Installing the Ink Cartridge 1. Turn on the printer. 2. Remove new ink cartridge from the pouch and remove the tape affixed to the front side. 3. Open front cover of the printer and pull the cartridge holder forward. 4. Take out old ink cartridge(s) and place new cartridge(s) into carriage. Hold round tab to ensure clean installation. Black cartridges go into left carriage, and color cartridges go into right carriage. Tab faces front of printer. 5. Close cartridge holder(s) and front cover. Tab Tape Metallic connector area Front cover Cartridge holder ※ Note The ink drop counter is automatically reset when the ink cartridge is installed. ◈ Using the Operation Panel • Power (LED) When turning on the power, a green LED will be lit. • Error (LED) When an error occurs, a red LED will be lit. (e.g. no paper, cover ajar, etc.) • Cartridge (LED) The LED will be lit when the ink has run out or the cartridge is removed. Check the status of the right cartridge with the right LED, and the left cartridge, with the left LED. For monochrome, the left LED is used. The left cartridge is black, and the right cartridge is color. • Clean (Button) Use this button to clean the ink cartridge heads. • Feed (Button) Press the FEED button once to discharge extra paper. Holding down the FEED button will discharge paper continuously until the button is released. ◈ Setting the DIP Switches Changing Dip Switch settings must be done when the printer is off. Any changes done while the printer is on will not be processed. 1. Serial Interface • DIP Switch 1 SW Function 1-1 Emulation 1-2 1-3 Auto Cutter 1-4 Cartridge 1-5 Density*1) 1-6 Special Function*2) 1-7 Near-End Sensor Status 1-8 Low Ink Check • DIP Switch 2 SW Function 2-1 Data Receive Error 2-2 2-3 Handshaking 2-4 Data Length 2-5 Parity Check 2-6 Parity Selection 2-7 2-8 Baud Rate Selection ON OFF Refer to the following table 1 Enable One cartridge Bold Enable Enable Disable Disable Two cartridges Normal Disable Disable Enable ON Print ? Reserved DTR/DSR 7 bits Enable EVEN OFF Ignore XON/XOFF 8bits Disable ODD Refer to the following table 2 Default OFF OFF OFF OFF OFF OFF OFF OFF Default OFF OFF OFF OFF OFF OFF OFF OFF 2. Parallel / USB Interface • DIP Switch 1 SW Function 1-1 Emulation 1-2 1-3 Auto Cutter 1-4 Cartridge 1-5 Density*1) 1-6 Special Function*2) 1-7 Near-End Sensor Status 1-8 Low Ink Check ON OFF Refer to the following table 1 Enable One cartridge Bold Enable Enable Disable Disable Two cartridges Normal Disable Disable Enable Default OFF OFF OFF OFF OFF OFF OFF OFF