Samsung WA45T3400AV/A4 User Manual - Page 27

STEP 6, Running a test cycle, Run calibration recommended

Get Samsung WA45T3400AV/A4 PDF manuals and user guides View all Samsung WA45T3400AV/A4 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

Installation STEP 6 Running a test cycle Run a test cycle as follows to check if your washer is properly installed. 1. Load about 6 pounds of laundry into the tub. 2. Press POWER to turn on your washer. 3. Select Rinse+Spin by turning the Cycle Selector. 4. Press START/PAUSE to start the test cycle. 5. The washer should not rock or vibrate excessively when water is supplied or when washing or spinning, and should drain well during the spin cycle. NOTE If water leaks while water is being supplied or drained, check the water connections. Refer to the "STEP 2 Connecting the water supply hose" section on page 20 for instructions. NOTE If the washer rocks and vibrates excessively, level your washer again. Refer to the "STEP 4 Leveling your washer" section on page 25 for instructions. STEP 7 Run calibration (recommended) Calibration ensures accurate weight detection by the washer. Make sure the tub is empty before running calibration. 1. Press POWER to turn on the washer. 2. Press and hold Temp. and Soil simultaneously for 3 seconds. 3. Press START/PAUSE to start calibration. 4. The tub rotates clockwise for approximately 2 minutes. 5. When complete, "0" appears on the display, and the washer turns off automatically. NOTE Run Calibration Mode periodically for more accurate weight detection. WA3400T_DC68-03850E-01_EN.indd 27 English 27 2020-07-07 PM 4:15:55

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
English 27
Installation
STEP 6
Running a test cycle
Run a test cycle as follows to check if your washer is properly installed.
1.
Load about 6 pounds of laundry into the tub.
2.
Press
POWER
to turn on your washer.
3.
Select
Rinse+Spin
by turning the
Cycle Selector
.
4.
Press
START/PAUSE
to start the test cycle.
5.
The washer should not rock or vibrate excessively when water is supplied or when
washing or spinning, and should drain well during the spin cycle.
NOTE
If water leaks while water is being supplied or drained, check the water connections. Refer to
the “
STEP 2
Connecting the water supply hose
” section on page
20
for instructions.
NOTE
If the washer rocks and vibrates excessively, level your washer again. Refer to the “
STEP
4 Leveling your washer
” section on page
25
for instructions.
STEP 7
Run calibration (recommended)
Calibration ensures accurate weight detection by the washer. Make sure the tub is empty
before running calibration.
1.
Press
POWER
to turn on the washer.
2.
Press and hold
Temp.
and
Soil
simultaneously for 3 seconds.
3.
Press
START/PAUSE
to start calibration.
4.
The tub rotates clockwise for approximately 2 minutes.
5.
When complete, “
0
” appears on the display, and the washer turns off automatically.
NOTE
Run Calibration Mode periodically for more accurate weight detection.
WA3400T_DC68-03850E-01_EN.indd
27
2020-07-07
PM 4:15:55