Samsung WF419AAU/XAA User Manual (ENGLISH) - Page 9

Drain facility, Flooring, Location consideration, Alcove or closet installation - 01

Get Samsung WF419AAU/XAA PDF manuals and user guides View all Samsung WF419AAU/XAA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

01 Installing your washer Drain facility The recommended height of the standpipe is 18 in (46 cm). The drain hose must be routed through the drain hose clip to the standpipe. The standpipe must be large enough to accept the outside diameter of the drain hose. The drain hose is attached at the factory. Flooring For best performance, your washer must be installed on a solidly constructed floor. Wood floor may need to be reinforced to minimize vibration and/or unbalanced load situations. Carpeting and soft tile surfaces are contributing factors in vibration and may cause your washer to move slightly during the spin cycle. Never install your washer on a platform or weakly supported structure. CAUTION Location consideration Do not install your washer in areas where water may freeze, since your washer will always maintain some water in its water valve, pump, and hose areas. This can cause damage the belts, the pump, hoses and other components. Alcove or closet installation MINIMUM CLEARANCES FOR CLOSET AND ALCOVE INSTALLATIONS: Sides - 1 In.(2.5 cm) Top - 17 In.(43.2 cm) Rear - 4 In.(10.2 cm) Closet Front - 2 In.(5.1 cm) If the washer and dryer are installed together, the closet front must have at least 72 in²(465 cm²) of an unobstructed air opening. Your washer alone does not require a specific air opening. BEST-WF419AAW-02657A_EN.indd 9 Installing your washer _9 2009-02-18 ¿ÀÈÄ 3:26:43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
Installing your washer
_9
Drain facility
The recommended height of the standpipe is 18 in (46 cm). The drain hose must be routed
through the drain hose clip to the standpipe. The standpipe must be large enough to accept the
outside diameter of the drain hose. The drain hose is attached at the factory.
Flooring
For best performance, your washer must be installed on a solidly constructed floor. Wood floor
may need to be reinforced to minimize vibration and/or unbalanced load situations. Carpeting
and soft tile surfaces are contributing factors in vibration and may cause your washer to move
slightly during the spin cycle.
Never install your washer on a platform or weakly supported structure.
Location consideration
Do not install your washer in areas where water may freeze, since your washer will always
maintain some water in its water valve, pump, and hose areas. This can cause damage the belts,
the pump, hoses and other components.
Alcove or closet installation
MINIMUM CLEARANCES FOR CLOSET AND ALCOVE INSTALLATIONS:
Sides – 1 In.(2.5 cm)
Rear – 4 In.(10.2 cm)
Top – 17 In.(43.2 cm)
Closet Front – 2 In.(5.1 cm)
If the washer and dryer are installed together, the closet front must have at least 72 in²(465 cm²)
of an unobstructed air opening. Your washer alone does not require a specific air opening.
01 Installing your washer
CAUTION
BEST-WF419AAW-02657A_EN.indd
9
2009-02-18
¿ÀÈÄ 3:26:43