Samsung WF455ARGSWR/AA Quick Guide Easy Manual Ver.1.0 (English) - Page 1
Samsung WF455ARGSWR/AA Manual
View all Samsung WF455ARGSWR/AA manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
WASHING MACHINE INSTALLATION GUIDE Parts supplied Tools needed Wrench Bolt hole covers Water supply hoses Hose guide Tie strap (option) Tape measure carpenter's level Pilers Flat screwdrilver 1 PREPARATION. 1. Check the installation location. □ CHECK : Solidly constructed floor (Not Carpeting and soft tile surfaces) 2. And move the washer to the installation location. * When installing the washer on a pedestal, do the installation before next step. 2 REMOVING ALL SHIPPING BOLTS. 5 CONNECTING THE DRAIN HOSE. Case 1. Wash basin Drain hose 'SFODIPOCBDL Ü 4QBOJTIPOCBDL Ü Case 2. Laundry tub 96" Max 18" Min Hose retainer Case 3. Stand pipe Hose retainer 8" Max 6" Min Tie strap 96" Max 18" Min Hose guide To keep the drain hose spout bent, use the supplied plastic hose guide. Tie strap The drain hose must be Laundry tub must be no placed at a height between shorter than 18 in (46 cm) 23.6 in (60cm) and 35.4 in and no longer than 96 in (90cm). (245 cm). Laundry tub must be no shorter than 18 in (46 cm) and no longer than 96 in (245 cm). Do not insert the drain hose too far into the stand pipe: 6 - 8 inches, and no more. 6 MOVE THE WASHER TO ITS FINAL LOCATION AND MAKE SURE IT IS LEVELED. Remove all shipping bolts at the back of washer with supplied spanner. Hold the shipping bolt Fill the holes with the with your hand and pull it supplied bolt hole covers. through the wide section of the hole. Repeat for each shipping bolt. CAUTION: Failure to remove the shipping bolts will cause vibration and noise. 3 COLD & HOT WATER HOSES INSTALLATION ON FAUCETS. HOT COLD Rubber washer Coupling Rubber washer Make sure a Rubber washer is inside each coupling on both ends. Tighten Coupling by hand until it is snug. Then tighten two-thirds of a Run water in a bowl or turn with pliers. basin to get rid of any debris inside hose. Check for HOT and Cold water supply. 4 WATER HOSES INSTALLATION ON WASHER. COLD (Left) Water HOT (Right) Water Connect one end of the COLD/HOT water supply hoses to the each COLD/ HOT water supply intakes at the back of the washer. Tighten Coupling by hand until it is snug. Then tighten two-thirds of a For proper operation, make turn with pliers. sure both Hot & Cold hoses from faucets are connected to the corresponding Hot / Cold water inlets on the washer. CAUTION: Make sure that the HOT & COLD hoses are switched with each other. Confirm whether washer is well seated and does not shake. Adjust leveling legs, if necessary. Your washer must be leveled on all four sides. Use a carpenter's level on all four corners of your washer to ensure it's level. 7 LEVEL THE WASHER BY ADJUSTING THE FOUR LEVELING LEGS. Level the washer by turning the leveling wheel in or out as required by using the supplied wrench. Check whether washer shakes and level again, if necessary. When your washer is leveled, tighten the locking nuts using the wrench or (-) flathead screwdriver. CAUTION: Your washer must be leveled on all four sides. An unlevel washer may cause vibration. 8 Final Test : Water leakage , Vibration & Noise 1. Powering your washing machine. 2. Run a test cycle(Rinse+Spin) with small amount of laundry such as 4~5 Towels. (1) Check for any leakage at the hose connections. If water leaks while water is being supplied or drained, check the water connections. (Refer to Step 3,4,5) (2) Check for vibration and noise. If the washer rocks and vibrates excessively, level your washer again. (Refer to Step 6,7) Visits by a Service Engineer to explain functions, maintenance or installation is not covered by warranty. INSTALLATION COMPLETION CHECKLIST □ Washer plugged in, power OK □ No water leakage □ Water hose connected properly □ Drain hose connected properly □ No vibration / noise □ Washer leveled □ Shipping bolts removed