Samsung WF45R6100AP/US User Manual - Page 52

Information codes, leaks. Once the leak issue is resolved, power the washer on.

Get Samsung WF45R6100AP/US PDF manuals and user guides View all Samsung WF45R6100AP/US manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

Troubleshooting Information codes If the washer fails to operate, you may see an information code on the screen. Check the table below and try the suggestions. Code 1C DC DC1 LC 4C 4C2 5C Action Check the water level sensor. • Power the washer off. Wait 2-3 minutes, power the washer on, and then try again. • Depending on the model, the drain system drains water automatically. The Power and Start/Pause (Hold to Start) buttons may be disabled during this process. The door is open. • Close the door and press Start/Pause (Hold to Start) to resume operation. Check the door switch. • Power the washer off. Wait 2-3 minutes, power the washer on, and then try again. Check for water leaks. • Power the washer off, and then check the drain system for any leaks. Once the leak issue is resolved, power the washer on. • Depending on the model, the drain system may drain water automatically. The Power and Start/Pause (Hold to Start) buttons may be disabled during this process. Check the water supply line. • Check the connection to the water lines (including water taps). • Power the washer off. Wait 2-3 minutes, power the washer on, and then try again. • Depending on the model, the drain system may drain water automatically. The Power and Start/Pause (Hold to Start) buttons may be disabled during this process. Laundry needs protection because the water being supplied is too hot. • Make sure the cold and hot water taps are properly connected. • Power the washer off. Wait 2-3 minutes, power the washer on, and then try again. Check the drain system. • Make sure the drain filter is not clogged. • If the drain filter is clogged, clean the filter, and then restart the washer. 52 English Troubleshooting Untitled-2 52 3/30/2020 12:25:56 PM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
Troubleshooting
English
52
Troubleshooting
Information codes
If the washer fails to operate, you may see an information code on the screen. Check the
table below and try the suggestions.
Code
Action
1C
Check the water level sensor.
•
Power the washer off. Wait 2-3 minutes, power the washer on, and
then try again.
•
Depending on the model, the drain system drains water
automatically. The
Power
and
Start/Pause (Hold to Start)
buttons
may be disabled during this process.
DC
The door is open.
•
Close the door and press
Start/Pause (Hold to Start)
to resume
operation.
DC1
Check the door switch.
•
Power the washer off. Wait 2-3 minutes, power the washer on, and
then try again.
LC
Check for water leaks.
•
Power the washer off, and then check the drain system for any
leaks. Once the leak issue is resolved, power the washer on.
•
Depending on the model, the drain system may drain water
automatically. The
Power
and
Start/Pause (Hold to Start)
buttons
may be disabled during this process.
4C
Check the water supply line.
•
Check the connection to the water lines (including water taps).
•
Power the washer off. Wait 2-3 minutes, power the washer on, and
then try again.
•
Depending on the model, the drain system may drain water
automatically. The
Power
and
Start/Pause (Hold to Start)
buttons
may be disabled during this process.
4C2
Laundry needs protection because the water being supplied is too hot.
•
Make sure the cold and hot water taps are properly connected.
•
Power the washer off. Wait 2-3 minutes, power the washer on, and
then try again.
5C
Check the drain system.
•
Make sure the drain filter is not clogged.
•
If the drain filter is clogged, clean the filter, and then restart the
washer.
Untitled-2
52
3/30/2020
12:25:56 PM