Samsung WF461ABP User Manual (user Manual) (ver.1.0) (English) - Page 11

Important Note To Installer

Get Samsung WF461ABP PDF manuals and user guides View all Samsung WF461ABP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

01 Installing your washer IMPORTANT NOTE TO INSTALLER Please read the following instructions carefully before installing the washer. These instructions should be retained for future reference. We recommend you hire a professional for installation of this washer. STEP 1 Removing the Shipping Bolts Before using your washer, you must remove the four shipping bolts from the back of the unit. 1. Loosen all the bolts with the supplied wrench. 2. Slide the bolt and spacer up and remove the bolt with the spacer through the hole in the rear wall of your washer. Repeat for each bolt. 3. Cover the holes with the supplied Bolt Hole Covers (See page 7). 4. Keep the shipping bolts and spacers for future use. STEP 2 Selecting a Location Before you install your washer, make sure the location: • Has a hard, level surface • Is away from direct sunlight • Has adequate ventilation • Will not freeze (tempuratures never below 32°F or 0°C) • Is away from heat sources such as oil or gas • Has enough room for the power cord. • Doesn't have any carpeting that will obstruct ventilation openings. STEP 3 Installing your Washer 1. If you use a stand pipe, make sure the connection between the drain hose and the standpipe is NOT airtight. The standpipe must be at least 18 in or 46 cm high. You must always exercise caution to avoid collapsing or damaging the drain hose. For best results, the drain hose should not be restricted in any way - by elbows, couplings, or excessive length. For situations where the drain hose cannot be conveniently elevated to at least 18 in or 46 cm, the drain hose must be supported. Do not insert the drain hose too far into 96" Max 18" Min the stand pipe: 6 - 8 inches, and no more. Laundry tub Stand pipe Hose retainer Tie strap 96" Max 18" Min WF431ABP-03016A-02_EN.indd Sec2:11 Installing your washer _11 2011-04-04 1:43:32

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
Installing your washer
_11
IMPORTANT NOTE TO INSTALLER
Please read the following instructions carefully before installing the washer.
These instructions should be retained for future reference.
We recommend you hire a professional for installation of this washer.
STEP 1
Removing the Shipping Bolts
Before using your washer, you must remove the four shipping
bolts from the back of the unit.
1.
Loosen all the bolts with the supplied wrench.
2.
Slide the bolt and spacer up and remove the bolt with the
spacer through the hole in the rear wall of your washer.
Repeat for each bolt.
3.
Cover the holes with the supplied Bolt Hole Covers (See page 7).
4.
Keep the shipping bolts and spacers for future use.
STEP 2
Selecting a Location
Before you install your washer, make sure the location:
•
Has a hard, level surface
•
Is away from direct sunlight
•
Has adequate ventilation
•
Will not freeze (tempuratures never below 32°F or 0°C)
•
Is away from heat sources such as oil or gas
•
Has enough room for the power cord.
•
Doesn’t have any carpeting that will obstruct ventilation openings.
STEP 3
Installing your Washer
1.
If you use a stand pipe, make sure the
connection between the drain hose and the
standpipe is NOT airtight. The standpipe
must be at least 18 in or 46 cm high.
You must always exercise caution to avoid
collapsing or damaging the drain hose.
For best results, the drain hose should
not be restricted in any way – by elbows,
couplings, or excessive length. For
situations where the drain hose cannot be
conveniently elevated to at least 18 in or
46 cm, the drain hose must be supported.
Do not insert the drain hose too far into
the stand pipe: 6 - 8 inches, and no more.
01 Installing your washer
96” Max
18” Min
96” Max
18” Min
Hose
retainer
Tie strap
Laundry tub
Stand pipe
WF431ABP-03016A-02_EN.indd Sec2:11
WF431ABP-03016A-02_EN.indd
Sec2:11
2011-04-04
1:43:32
2011-04-04
1:43:32