Samsung WF520ABP/XAA User Manual (user Manual) (ver.1.0) (English) - Page 16

Step 3 - 27 '

Get Samsung WF520ABP/XAA PDF manuals and user guides View all Samsung WF520ABP/XAA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

installing your washer STEP 3 Installing your Washer 1. Place the drain hose in the drain facility. Be sure an airtight connection is NOT made between the drain hose and the standpipe. The standpipe must be at least 18 in or 46 cm high. Caution must always be exercised to avoid collapsing or damaging the drain hose. For best results, the drain hose should not be restricted in any way - by elbows, couplings, or excessive lengths. For situations where the drain hose cannot be conveniently elevated to at least 18 in or 46 cm, the drain hose must 96" Max be supported. 18" Min Laundry tub Stand pipe Hose retainer Tie strap 96" Max 18" Min 2. Check the inlet hose to ensure a washer is inside each fill Cold hose. Thread the inlet hoses to the HOT and COLD faucet connections. On the other end of the hose, check for one rubber washer per hose and install each fill hose to the water valve. Make sure the hose with the Hot printed line is attached to the HOT faucet. Tighten by hand until snug, then two-thirds of a turn with pliers. Hot Rubber Washer For correct water use, connect both HOT and COLD water valves. If either or both are not connected, an "nF" (no fill) error can occur. Cold printed Hot printed 3. Turn on the "HOT" and "COLD "water supply and check all connections at the water valve and the faucet for leaks. 16_ installing your washer WF520AB-02838A_EN.indd 16 2010-03-24 ¿ÀÈÄ 4:30:27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
16_
installing your washer
STEP 3
Installing your Washer
1.
Place the drain hose in the drain facility. Be
sure an airtight connection is NOT made
between the drain hose and the standpipe.
The standpipe must be at least 18 in or 46
cm high.
Caution must always be exercised to
avoid collapsing or damaging the drain
hose. For best results, the drain hose
should not be restricted in any way – by
elbows, couplings, or excessive lengths.
For situations where the drain hose
cannot be conveniently elevated to at
least 18 in or 46 cm, the drain hose must
be supported.
2.
Check the inlet hose to ensure a washer is inside each fill
hose.
Thread the inlet hoses to the HOT and COLD faucet
connections.
On the other end of the hose, check for one rubber washer
per hose and install each fill hose to the water valve. Make
sure the hose with the Hot printed line is attached to the
HOT faucet. Tighten by hand until snug, then two-thirds of a
turn with pliers.
For correct water use, connect both HOT and COLD water
valves. If either or both are not connected, an “nF” (no fill)
error can occur.
3.
Turn on the “HOT” and “COLD “water supply and check all
connections at the water valve and the
faucet for leaks
.
installing your washer
96” Max
18” Min
96” Max
18” Min
Hose
retainer
Tie strap
Laundry tub
Stand pipe
Cold
Hot
Cold printed
Hot printed
Rubber Washer
WF520AB-02838A_EN.indd
16
2010-03-24
¿ÀÈÄ 4:30:27