Sanyo DP32670 Owners Manual - Page 20
Memorizing channels - base
UPC - 086483077494
View all Sanyo DP32670 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 20 highlights
Memorizing channels This TV is equipped with a channel memory feature which allows channels to skip up or down to the next channel set into memory, skipping over unwanted channels. Before selecting channels, they must be programmed into the TV's memory. To use this TV with an antenna, set the Signal Type option to the Air mode. When shipped from the factory, this menu option is in the Cable mode. Air/Cable selection 1 Select "Channel", then press ▶ or ENTER. 2 Press ▲ or ▼ to select "Auto Ch Memory", then press ▶ or ENTER. 3 Press ▲ or ▼ to select "Signal Type". 4 Press ◀ or ▶ to select "Air" or "Cable". Air - VHF/UHF channels Cable - CABLE TV channels Auto Ch Memory Signal Type Automatic Search Cable Start : Select : Adjust CABLE CHART The chart below is typical of many cable system channel allocations. 4 The TV will begin memorizing all the channels available in your area. • It may take from 15 minutes to 30 minutes to complete memorizing digital cable channels. Depending on the reception condition, a bar display may not advance for several minutes, please be patient. NOTE: • Memorizing channels is best accomplished during evening "PRIMETIME" hours, as more stations are broadcasting digital signals. Memorizing channels can only be accomplished while a station is broadcasting a digital signal to set that channel into memory. • If you are unsure of the digital channels available in your area, you may visit www.antennaweb.org to receive a list based on your address or zip code. Should you require further assistance you may call our toll-free customer service line at 1-800-877-5032. • New digital channels may be added to your area periodically, it is recommended to perform the "Automatic Search" procedure regularly. Adding Channel If you find a new digital channel unregistered, you can add the new channel into the channel memory. 1 Tune in the new channel. 2 Select "Channel", then press ▶ or ENTER. 3 Press ▲ or ▼ to select "Add/Delete", then press ▶ or ENTER. Add/Delete Adding Channel >> Add/Delete >> Clear All >> NOTE: • It may take a few seconds for a digital channel picture to appear on screen after being selected. Automatic Search 1 Select "Channel", then press ▶ or ENTER. 2 Press ▲ or ▼ to select "Auto Ch Memory", then press ▶ or ENTER. 3 Press ▲ or ▼ to select "Automatic Search", then press ▶ or ENTER. Auto Ch Memory Signal Type Automatic Search Cable Stop Analog Channel Found : 7 Digital Channel Found : 5 Programming Now : Select ENTER:Cancel 20 : Select ENTER:Set 4 Press ▲ or ▼ to select "Adding Channel", then press ▶ or ENTER. The new channel will be added into the channel memory. Add/Delete channel You can select the channel that you want to skip. 1 Select "Channel", then press ▶ or ENTER. 2 Press ▲ or ▼ to select "Add/Delete", then press ▶ or ENTER. 3 Press ▲ or ▼ to select "Add/Delete", then press ▶ or ENTER. 4 Press ▲ or ▼ to select the channel that you want to skip. Add/Delete CH 2 3 3-1 3-2 4 Signal Analog Analog Digital Digital Analog Add Add Delete Add Delete : Select : Adjust 5 Press ◀ or ▶ to select "Add" or "Delete", whichever function you want to perform. 6 Repeat steps 4 - 5 for other channels you want to add or delete. 54H0521A_eng.indd 20 3/17/10 4:27:56 PM