Sanyo HT27547 Owners Manual - Page 1
Sanyo HT27547 Manual
View all Sanyo HT27547 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
VIDEO2 COMPONENT: GREEN, BLUE, RED-An Exceptional picture CONNECTING A DVD OR GAME SYSTEM 1 Connect a Component Cable to the VIDEO2 Green, Blue, and Red video jacks as shown. 2 Connect an Audio Cable to the VIDEO2 White and Red audio jacks. 3 Press INPUT to select Component2 to view the program. Note: Audio / Video Input (VIDEO2) and Component inputs share the same audio (R/L) input jacks. IMPORTANT NOTE: These jacks accept only 480i (standard interlaced) signals. OPERATING TIPS: I Press the INPUT key after connecting cables to access the AV Inputs. There is NO need to tune to a blank channel. I You DO NOT need to tune the DTV to Channel 3 or 4 to view a DVD program. DVD PLAYER or similar device DTV BACK VIDEO2 12 AUDIO L/R JACKS 1 GREEN, BLUE, RED JACKS GAME SYSTEM AUDIO L/R JACKS 2 1 GREEN, BLUE, RED JACKS ENGLISH AS SDTV Owner's Manual Part No.: 1JC6P1P0255A - PLEASE CALL US AT 1.800.877.5032 IF YOU NEED ASSISTANCE WITH YOUR NEW SANYO 27-INCH SDTV. WE CAN HELP! Model No. HT27547 Visit us at www.sanyoctv.com for more information about this model. Printed in U.S.A. SMC, March 2007 • 29-H3DSA • VB9G • GXBD FIRST-THINGS-FIRST (REQUIRED INITIAL SETUP) 1 Install batteries in remote control (2AAA, not included) DIGITAL AUDIO JACK CONNECTING A MULTICHANNEL RECEIVER TO THE DTV 1 Connect a Multichannel Receiver to the DTV Digital Audio Output as shown. Note: Dolby ® Digital 5.1 audio is available at the Digital Audio Output only when received as part of a Digital Antenna signal being viewed on the screen. MULTICHANNEL RECEIVER CONNECTING A STEREO AMPLIFIER TO THE DTV AUDIO OUT (FIXED ANALOG) JACKS 1 Connect a Stereo Amplifier to the DTV Audio Out jacks as shown. Note: Do not connect external speakers directly to the DTV. 1 OPTICAL DIGITAL CABLE (Not supplied) BACK VIEW OF DTV 1 BACK VIEW OF DTV OPERATING TIP: A Digital Audio signal is available only when received as part of a Digital RF signal. STEREO AMPLIFIER OPERATING TIP: Position your DTV at least 2 feet from stereo speakers. The magnets in the speakers may affect the picture quality. If you experience problems, please call 1-800-877-5032, We Can Help! « REMOTE CONTROL OPERATION Input Key-Press to change the input signal source as follows: Analog RF ¬ Digital RF ¬ Video1 ¬ Video2 ¬ Component2 ¬ Analog RF. Number Keys-Two keys must be pressed to select a direct channel. Example: Press 0 then 6 to select channel 6. For Analog Cable channels above 100, press and hold the 1 key until C1- - appears, then press the other two numbers. Info Key-Press to display the Digital and Analog Full Banner information which includes: Channel Number (Major and Minor), Tuner ID., Station ID, V-Chip Program Rating, Program Title, Audio Info, and Signal Strength, if available. (Press again to remove the display.) Recall Key-Press to switch between the last two channels. The RECALL key cannot toggle between a Digital channel and an Analog channel. See TUNER (#5) key description. Tuner Key-Use this key to toggle from one tuning system to another, digital channels and analog channels. Note: The TUNER key is inactive when an external input is selected (Video1, Video2, or Component2). Menu Navigational Keys: Menu-Press to display the on-screen menu. Cursor L (up) M (down) keys-Use these keys to move the cursor up and down within the menu. Cursor < (left) > (right) keys-Use these keys to move the cursor left and right within the menu. Enter Key-Press to select an option from the menu system, when required. Exit Key-Press to exit from the menu system. Caption Key-Press to select mode options: Digital CC1 ~ Digital CC6, or Analog CC1 ~ CC4, OFF, or QuikCap. (QuikCap switches captions on and off with the Mute function.) Digital Captions can be changed using the menu settings Channel Scanning (CH LM ) Keys-Press to scan through the channels in memory. Volume Keys-Press VOL - + to adjust. PIX Shape Key-Use to change the video display format. Available options depend on signal received and the broadcast's aspect ratio. Note: Cannot display picture on a full screen. Check Aspect Ratio of broadcast. Then press PIX SHAPE key to change setting. Audio Key-Press to select the desired audio mode (if available). POINT TOWARD DTV 11 12 13 11 Sleep Key-Press this key then the "0" key to set the Sleep Off Timer. Time can be set in 30minute increments up to 3 hours. Note: The Sleep Timer cancels when the TV is turned off or if a power failure occurs. 12 Mute Key-Press once to mute the sound. 13 Reset Key-Press this key twice to restore fac- tory settings. The TV will automatically start Channel Search and clear all customized settings. Note: Channel scan memory database of digital and analog channels will be replaced. If desired, personal settings can be made again using the menu options. PRECAUTIONS To ensure safe operation, please observe the following precautions: Replace both batteries at the same time. Do not use a new battery with a used battery. Risk of explosion, if battery is replaced by an incorrect type. Do not expose the Remote Control Unit to moisture or heat. 2 Connect Signal to the TV's Digital & Analog 75 ohm Input terminal Digital (DTV) RF Antenna Connection Analog RF Antenna Connection Connect an RF antenna to the Digital Antenna In terminal. RF ANTENNA DTV BACK Connect a Cable signal (with or without a cable box) or RF antenna to the Analog RF input. RF ANALOG ANTENNA CABLE CABLE BOX OR SATELLITE BOX DTV BACK NOTES: The tuner in this DTV receives HD signals from an antenna. Digital signals from a Set-top (STB) Box are received through the Component In jacks. This DTV can receive ANY unscrambled RF signal being broadcast. 3 Plug in AC power cord. 4 Press the POWER key to turn on the TV. (Follow on-screen instructions) 5 MUST perform TV "All Channel Search." The All Channel Search contains two processes that are executed simultaneously for digital and analog channels. If after two searches the TV still fails to detect any channels, the TV will tune to analog channel 3. These two channel searches are necessary even if you plan to use the TV only as a monitor. OR OR Specifications Power Requirement: Source: AC 120V, 60Hz Power Consumption: 85 watts Channel Search [Analog & Digital] on-screen display « CONNECTING A VIDEO GAME TO THE DTV FRONT A/V (VIDEO1) JACKS 1 Connect a Composite Cable to the VIDEO1 Yellow, White, and Red AV jacks as shown. 2 Press DTV remote control INPUT key to select Video1 to view program. GAME 1 SYSTEM CONNECTING A VCR OR DVD TO THE DTV ANALOG VIDEO2 JACKS 1 Connect a Composite Cable to the VIDEO2 Yellow, White, and Red AV jacks as shown. 2 Optional Connect DVD to the TV's S-Video jack as shown. Note: S-Video jack connections override Video jack connection (VIDEO2). 3 Press DTV remote control INPUT key to select Video2 to view the VCR or DVD program. VCR or DVD S-VIDEO JACK 2 1 IMPORTANT NOTE FOR MONITOR USE: If you did not connect an antenna, you must run All Channel Search twice before you can use the INPUT key to select the AV input signals. OPERATING TIPS: I For Mono VCR (Single Audio Jack), connect VCR Audio Out to DTV Audio (L) Input. I "No Signal" will appear randomly on the screen when no signal is detected at the VIDEO1 or VIDEO2 video jack. DTV VIDEO2 AV INPUT JACKS REMOTE CONTROL 3