Sanyo VCC-9684VA Instruction Manual - Page 2

INSTALLATION 1 Remove the dome cover. Push Preparation 2 Remove the blue tape, air cushion and screw. Do not touch the lens and lens barrel. 3 Turn the lens 90 degrees clockwise. 4 Screw 5 Loosen the black screw. 1 Blue tape 2 Air cushion A Installing on the Ceiling 1 Connect the cables from the ceiling. 2 Mount the camera unit to the base plate. 2 1 Power cables B Installing on the Wall 1 Set the lens in the correct direction. 1 Remove the black screw A. 2 Turn the lens in the arrow direction to reverse the orientation. 3 Confirm that the dials are located at the top. 4 Temporarily tighten the removed black screw A. 2 3 14 Push the camera unit until it clicks taking care not to pinch the cable. A Black screw 2 Connect the cables from the wall. 3 Mount the camera unit to the base plate. Supplied screw Make sure that the camera unit and base plate fit perfectly. 2 3 Supplied screw Push the camera unit until it clicks taking care not to pinch the cable. Make sure that the camera unit and base plate fit perfectly. ADJUSTING CAMERA IMAGE Español Français English b Checks on monitor Camera adjustments/settings Connect a portable monitor. MONITOR OUT The camera comes pre-adjusted and ready to install at the time of factory shipment, but you can make adjustments or settings if you need. If you have trouble adjusting the camera, consult your dealer or an Authorized Sanyo Service Center. GND A dedicated MONITOR OUT connector is provided for portable monitor. b Angle-of-view adjustment Adjust the angle of view by moving the lens unit. 200 (Ceiling Installed) (Wall Installed) ● Do not touch the lens and lens barrel. ● When rotating the lens unit, make sure a metal edge does not damage the cables. b Zoom and focus B A DC 1 Zoom 2 Focus Loosen the zoom ring knob A, and turn the zoom ring B to zoom in Loosen the focus ring knob C, and turn the focus ring D to focus on or out. the object. When finished, tighten the zoom and focus ring knobs AC securely. When monitoring lighting or other extremely bright objects (which exceed the maximum required illumination), smearing may occur in the vertical or horizontal direction (either above and below the high-brightness object or as a perpendicular band). In such a case, adjust the angle of illumination and other factors while observing the monitor. ● Electronic shutter speed setting (unit: second) 1/60 1/100 1/1000 1/2000 12 12 12 Switch1: MSB Switch2: LSB 12 • Using the high speed electronic shutter indoors with low lighting, will give darker pictures. In such a case, add some lights to make sure the lighting is sufficient. • If the lighting is very bright, pay attention to the light angle in order to avoid or minimize the smear phenomenon effect. ● Aperture compensation Sharp outline Normal outline ● White balance (color compensation) Manual White Balance Auto-Tracing White balance (ATW) MWB 6 RED BLUE Turn clockwise to augment the color. ● Sync setting Line-Lock Synchronizes the unit with power frequency* LL 6 Internal sync 3 3 ● Backlight compensation Only when using an auto-iris lens Multi-spot metering Backlight compensation to the entire screen* Center zone metering Backlight compensation to the central portion of the screen High Normal 45 45 45 OFF 45 * If the background of the object is extremely dark, set to Center zone metering. 7 PHASE 7 * Adjust the roll by turning the LINE PHASE dial on the second and subsequent cameras. If the vertical roll cannot be corrected by adjusting the LINE PHASE dial on the second and subsequent cameras, try adjusting the LINE PHASE dial on the first camera. If it still cannot be corrected, please check that the polarity of the power cords of all connected devices is correct. ● Lens iris level adjustment If the entire image is too dark or too bright, adjust the condition. Low (darker) A. I. LENS High (brighter) LEVEL After finishing camera adjustments/settings ... 1 Tighten the screw. 2 Install the dome cover. 1 Push the dome cover until it clicks. 1 1 For wall installation, securely tighten the screw you temporarily tightened. 2 2 While holding down the dome cover, turn it in the direction of the arrow until the lens is completely visible through the camera window.