Sanyo XC50 Instruction Manual, PLC-XC50 - Page 61

ORDER REPLACEMENT LAMP, Maintenance and Care, ● Model No. of your projector, PLC-XC50 / PLC-XC55 - plc lamp

Get Sanyo XC50 - PLC XGA LCD Projector PDF manuals and user guides
UPC - 086483072062
View all Sanyo XC50 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

Maintenance and Care Follow these steps to replace the lamp. 1 Turn off the projector and disconnect the AC power cord. Allow the projector to cool for at least 45 minutes. 2 Loosen the screw with a screwdriver, slide and open the lamp cover. 3 Loosen 2 screws of the lamp with a screwdriver and pull out the lamp upwards vertically by grasping the handle. 4 Replace the lamp with a new one and tighten the 2 screws back into position. Make sure that the lamp is set properly. Replace the lamp cover and tighten the screw. 5 Connect the AC power cord to the projector and turn on the projector. 6 Reset the lamp replacement counter. See "Resetting the Lamp Counter" on the next page . Lamp Cover Screw Handle Screw Screw Lamp ORDER REPLACEMENT LAMP Replacement lamp can be ordered through your dealer. When ordering a projection lamp, give the following information to the dealer. ● Model No. of your projector : PLC-XC50 / PLC-XC55 ● Replacement Lamp Type No. : POA-LMP127 (Service Parts No. 610 339 8600) 61

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
61
Follow these steps to replace the lamp.
Turn off the projector and disconnect the AC power
cord. Allow the projector to cool for at least 45
minutes.
Loosen 2 screws of the lamp with a screwdriver and
pull out the lamp upwards vertically by grasping the
handle.
Replace the lamp with a new one and tighten the 2
screws back into position.
Make sure that the lamp is
set properly.
Replace the lamp cover and tighten the
screw.
Loosen the screw with a screwdriver, slide and open
the lamp cover.
Connect the AC power cord to the projector and turn
on the projector.
Reset the lamp replacement counter°
See "Resetting the Lamp Counter" on the next page .
1
2
3
4
5
6
ORDER REPLACEMENT LAMP
Replacement lamp can be ordered through your dealer.
When ordering a projection lamp, give
the following information to the dealer.
● Model No. of your projector
: PLC-XC50 / PLC-XC55
● Replacement Lamp Type No.
: POA-LMP127
(Service Parts No.
610 339 8600)
Lamp
Handle
Screw
Screw
Lamp Cover
Maintenance and Care
Screw