Schwinn 150 Upright Bike Assembly and Owner's Manual - Page 28

Power-Up / Idle Mode, Auto Shut-Off Sleep Mode, Initial Setup, Quick Start / Manual Program

Get Schwinn 150 Upright Bike PDF manuals and user guides View all Schwinn 150 Upright Bike manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

Power-Up / Idle Mode The Console will enter Power-Up / Idle Mode if it is plugged into a power source, any button is pushed, or if it receives a signal from the RPM sensor as a result of pedaling the machine. Auto Shut-Off (Sleep Mode) If the Console does not receive any input in approximately 5 minutes, it will automatically shut off. The LCD display is off while in Sleep Mode. Note: The Console does not have an On/Off switch. Initial Setup During the first power-up, the Console must be setup for your preferred measurement units, the machine type, and brightness of the screen. 1. Units of Measurement: Push the Increase/Decrease buttons to change between "Miles-Lb" (Imperial English) or "Km-Kg" (metric). 2. Push START/ENTER to set. 3. Machine Type: Push the Increase/Decrease buttons to change between "BIKE" and "ELLIPTICAL". 4. Push START/ENTER to set. 5. Backlight: Push the Increase/Decrease buttons to change the screen contrast, with "1" the lowest and "5" the highest. 6. Push START/ENTER to set. The Console goes back to the Power-Up / Idle Mode screen. Note: To change these choices, consult the "Console Set-Up Mode" section. Quick Start / Manual Program The Quick Start / Manual program lets you start a workout without entering any information. 1. Sit on the machine. 2. Push the QUICK START button to start the QUICK START / MANUAL program. 3. To change the resistance level, push the Increase/Decrease buttons. The current interval and future intervals are set to the new level. The default Quick Start resistance level is 3. The time will count up from 00:00. Note: The maximum time value is 99:59. 4. When done with your workout, stop pedaling and push STOP to pause the workout. Push STOP again to end the workout. 28

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
28
Power-Up / Idle Mode
The Console will enter Power-Up / Idle Mode if it is plugged into a power source, any button is
pushed, or if it receives a signal from the RPM sensor as a result of pedaling the machine.
Auto Shut-Off (Sleep Mode)
If the Console does not receive any input in approximately 5 minutes, it will automatically shut
off. The LCD display is off while in Sleep Mode.
Note:
The Console does not have an On/Off switch.
Initial Setup
During the first power-up, the Console must be setup for your preferred measurement units, the
machine type, and brightness of the screen.
1.
Units of Measurement:
Push the Increase/Decrease buttons to change between “Miles-Lb”
(Imperial English) or “Km-Kg” (metric).
2.
Push START/ENTER to set.
3.
Machine Type: Push the Increase/Decrease buttons to change between “BIKE” and
“ELLIPTICAL”.
4.
Push START/ENTER to set.
5.
Backlight: Push the Increase/Decrease buttons to change the screen contrast, with “1” the
lowest and “5” the highest.
6.
Push START/ENTER to set. The Console goes back to the Power-Up / Idle Mode screen.
Note:
To change these choices, consult the “Console Set-Up Mode” section.
Quick Start / Manual Program
The Quick Start / Manual program lets you start a workout without entering any information.
1.
Sit on the machine.
2.
Push the QUICK START button to start the QUICK START / MANUAL program.
3.
To change the resistance level, push the Increase/Decrease buttons. The current interval
and future intervals are set to the new level. The default Quick Start resistance level is 3. The
time will count up from 00:00.
Note:
The maximum time value is 99:59.
4.
When done with your workout, stop pedaling and push STOP to pause the workout. Push
STOP again to end the workout.