Home » Seagate Manuals » Hard Drives » Seagate ST1000DM003 » Manual Viewer

Seagate ST1000DM003 Barracuda 7200.10 SATA Product Manual - Page 47

Configuring and mounting the drive - board

View all Seagate ST1000DM003 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

3.0 Configuring and mounting the drive This section contains the specifications and instructions for configuring and mounting the drive. 3.1 Handling and static-discharge precautions After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic discharge (ESD) hazards. Observe the following standard handling and static-discharge precautions: Caution: • Before handling the drive, put on a grounded wrist strap, or ground yourself frequently by touching the metal chassis of a computer that is plugged into a grounded outlet. Wear a grounded wrist strap throughout the entire installation procedure. • Handle the drive by its edges or frame only. • The drive is extremely fragile-handle it with care. Do not press down on the drive top cover. • Always rest the drive on a padded, antistatic surface until you mount it in the computer. • Do not touch the connector pins or the printed circuit board. • Do not remove the factory-installed labels from the drive or cover them with additional labels. Removal voids the warranty. Some factory-installed labels contain information needed to service the drive. Other labels are used to seal out dirt and contamination. Barracuda 7200.10 Serial ATA Product Manual, Rev. K 41

Section	Page
1.0 Introduction	7
1.1 About the Serial ATA interface	8
2.0 Drive specifications	9
2.1 Specification summary tables	9
2.2 Formatted capacity	32
2.2.1 LBA mode	32
2.3 Default logical geometry	32
2.4 Recording and interface technology	33
2.5 Physical characteristics	34
2.6 Seek time	35
2.7 Start/stop times	35
2.8 Power specifications	36
2.8.1 Power consumption	36
2.8.1.1 Typical current profiles	37
2.8.2 Conducted noise	37
2.8.3 Voltage tolerance	37
2.8.4 Power-management modes	38
2.9 Environmental specifications	39
2.9.1 Ambient temperature	39
2.9.2 Temperature gradient	39
2.9.3 Humidity	39
2.9.3.1 Relative humidity	39
2.9.3.2 Wet bulb temperature	39
2.9.4 Altitude	39
2.9.5 Shock	39
2.9.5.1 Operating shock	39
2.9.5.2 Nonoperating shock	40
2.9.6 Vibration	40
2.9.6.1 Operating vibration	40
2.9.6.2 Nonoperating vibration	40
2.10 Acoustics	41
2.10.1 Test for Prominent Discrete Tones (PDTs)	41
2.11 Electromagnetic immunity	42
2.12 Reliability	43
2.12.1 Annualized Failure Rate (AFR) and Mean Time Between Failures (MTBF)	43
2.13 Agency certification	43
2.13.1 Safety certification	43
2.13.2 Electromagnetic compatibility	43
2.13.3 FCC verification	44
2.14 Environmental protection	45
2.14.1 European Union Restriction of Hazardous Substances (RoHS) Directive	45
2.14.2 China Restriction of Hazardous Substances (RoHS) Directive	45
2.15 Corrosive environment	45
3.0 Configuring and mounting the drive	47
3.1 Handling and static-discharge precautions	47
3.2 Configuring the drive	48
3.3 Serial ATA cables and connectors	48
3.4 Drive mounting	49
4.0 Serial ATA (SATA) interface	51
4.1 Hot-Plug compatibility	51
4.2 Serial ATA device plug connector pin definitions	52
4.3 Supported ATA commands	53
4.3.1 Identify Device command	55
4.3.2 Set Features command	59
4.3.3 S.M.A.R.T. commands	60
5.0 Seagate Technology support services	61
Index	63
A	63
B	63
C	63
D	63
E	63
F	63
G	63
H	63
I	64
K	64
L	64
M	64
N	64
O	64
P	64
Q	64
R	64
S	65
T	65
U	65
V	65

Match case Limit results 1 per page

Barracuda 7200.10 Serial ATA Product Manual, Rev. K

3.0

Configuring and mounting the drive

This section contains the specifications and instructions for configuring and mounting the drive.

3.1

Handling and static-discharge precautions

After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic dis-

charge (ESD) hazards. Observe the following standard handling and static-discharge precautions:

Caution:

•

Before handling the drive, put on a grounded wrist strap, or ground yourself frequently by touching the metal

chassis of a computer that is plugged into a grounded outlet. Wear a grounded wrist strap throughout the entire

installation procedure.

•

Handle the drive by its edges or frame

only

•

The drive is extremely fragile—handle it with care. Do not press down on the drive top cover.

•

Always rest the drive on a padded, antistatic surface until you mount it in the computer.

•

Do not touch the connector pins or the printed circuit board.

•

Do not remove the factory-installed labels from the drive or cover them with additional labels. Removal voids

the warranty. Some factory-installed labels contain information needed to service the drive. Other labels are

used to seal out dirt and contamination.