Home » Seagate Manuals » Hard Drives » Seagate ST3000DM001 » Manual Viewer

Seagate ST3000DM001 Barracuda 7200.11 SATA Product Manual - Page 13

Serial ATA Revision 2.5 specification - warranty

View all Seagate ST3000DM001 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

Drive specification Vibration, operating Vibration, nonoperating Drive acoustics, sound power Idle** Performance Seek Quiet Seek Nonrecoverable read errors Annualized Failure Rate (AFR) Warranty Contact start-stop cycles Supports Hotplug operation per the Serial ATA Revision 2.5 specification ST3640323AS 2-22 Hz: 0.25 Gs, Limited displacement 22-350 Hz: 0.50 Gs 350-500 Hz:: 0.25 Gs 5-22 Hz: 2.0 Gs 22-350 Hz: 5.0 Gs 350-500 Hz:: 2.0 Gs ST3640623AS 2.6 bels (typical) 2.8 bels (max) 3.0 bels (typical) 3.2 bels (max) 2.7 bels (typical) 2.9 bels (max) 1 per 1014 bits read 0.34% To determine the warranty for a specific drive, use a web browser to access the following web page: support.seagate.com/customer/warranty_validation.jsp From this page, click on the "Verify Your Warranty" link. You will be asked to provide the drive serial number, model number (or part number) and country of purchase. The system will display the warranty information for your drive. 50,000 at 25°C, 50% rel. humidity Yes *One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting. **During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and power to operational levels. Barracuda 7200.11 Serial ATA Product Manual, Rev. E 7

Section	Page
1.0 Introduction 1	3
1.1 About the Serial ATA interface 2	3
2.0 Drive specifications 3	3
2.1 Formatted capacity 10	3
2.1.1 LBA mode 10	3
2.2 Default logical geometry 10	3
2.3 Recording and interface technology 10	3
2.4 Physical characteristics 11	3
2.5 Seek time 11	3
2.6 Start/stop times 12	3
2.7 Power specifications 12	3
2.7.1 Power consumption 12	3
2.7.2 Conducted noise 14	3
2.7.3 Voltage tolerance 14	3
2.7.4 Power-management modes 14	3
2.8 Environmental specifications 15	3
2.8.1 Ambient temperature 15	3
2.8.2 Temperature gradient 15	3
2.8.3 Humidity 15	3
2.8.4 Altitude 15	3
2.8.5 Shock 15	3
2.8.6 Vibration 16	3
2.9 Acoustics 17	3
2.9.1 Test for Prominent Discrete Tones (PDTs) 17	3
2.10 Electromagnetic immunity 17	3
2.11 Reliability 18	3
2.11.1 Annualized Failure Rate (AFR) and Mean Time Between Failures (MTBF) 18	3
2.12 Agency certification 18	3
2.12.1 Safety certification 18	3
2.12.2 Electromagnetic compatibility 18	3
2.12.3 FCC verification 19	3
2.13 Environmental protection 20	3
2.13.1 European Union Restriction of Hazardous Substances (RoHS) Directive 20	3
2.14 Corrosive environment 20	3
3.0 Configuring and mounting the drive 21	3
3.1 Handling and static-discharge precautions 21	3
3.2 Configuring the drive 22	3
3.3 Serial ATA cables and connectors 23	3
3.4 Drive mounting 24	3
4.0 Serial ATA (SATA) interface 27	3
4.1 Hot-Plug compatibility 27	3
4.2 Serial ATA device plug connector pin definitions 28	3
4.3 Supported ATA commands 29	3
4.3.1 Identify Device command 31	3
4.3.2 Set Features command 35	3
4.3.3 S.M.A.R.T. commands 36	3
5.0 Seagate Technology support services 37	3
Figure 1. Serial ATA connectors 22	5
Figure 2. Attaching SATA cabling 23	5
Figure 3. Mounting dimensions (1500, 1000 and 640 GB models) 24	5
Figure 4. Mounting dimensions (320 and 160 GB models) 25	5
1.0 Introduction	7
1.1 About the Serial ATA interface	8
2.0 Drive specifications	9
2.1 Formatted capacity	16
2.1.1 LBA mode	16
2.2 Default logical geometry	16
2.3 Recording and interface technology	16
2.4 Physical characteristics	17
2.5 Seek time	17
2.6 Start/stop times	18
2.7 Power specifications	18
2.7.1 Power consumption	18
2.7.2 Conducted noise	20
2.7.3 Voltage tolerance	20
2.7.4 Power-management modes	20
2.8 Environmental specifications	21
2.8.1 Ambient temperature	21
2.8.2 Temperature gradient	21
2.8.3 Humidity	21
2.8.3.1 Relative humidity	21
2.8.3.2 Wet bulb temperature	21
2.8.4 Altitude	21
2.8.5 Shock	21
2.8.5.1 Operating shock	21
2.8.5.2 Nonoperating shock	22
2.8.6 Vibration	22
2.8.6.1 Operating vibration	22
2.8.6.2 Nonoperating vibration	22
2.9 Acoustics	23
2.9.1 Test for Prominent Discrete Tones (PDTs)	23
2.10 Electromagnetic immunity	23
2.11 Reliability	24
2.11.1 Annualized Failure Rate (AFR) and Mean Time Between Failures (MTBF)	24
2.12 Agency certification	24
2.12.1 Safety certification	24
2.12.2 Electromagnetic compatibility	24
2.12.3 FCC verification	25
2.13 Environmental protection	26
2.13.1 European Union Restriction of Hazardous Substances (RoHS) Directive	26
2.14 Corrosive environment	26
3.0 Configuring and mounting the drive	27
3.1 Handling and static-discharge precautions	27
3.2 Configuring the drive	28
3.3 Serial ATA cables and connectors	29
3.4 Drive mounting	30
4.0 Serial ATA (SATA) interface	33
4.1 Hot-Plug compatibility	33
4.2 Serial ATA device plug connector pin definitions	34
4.3 Supported ATA commands	35
4.3.1 Identify Device command	37
4.3.2 Set Features command	41
4.3.3 S.M.A.R.T. commands	42
5.0 Seagate Technology support services	43
Index	45
A	45
B	45
C	45
D	45
E	45
F	45
G	45
H	45
I	46
K	46
L	46
M	46
N	46
O	46
P	46
Q	46
R	46
S	47
T	47
U	47
V	47