Home » Seagate Manuals » Hard Drives » Seagate ST3000VX000 » Manual Viewer

Seagate ST3000VX000 SV35.2 Series PATA Product Manual - Page 11

Drive specification, ST3750640AV, ST3500630AV

View all Seagate ST3000VX000 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Drive specification Vibration, operating Vibration, nonoperating Drive acoustics, sound power (bels) Idle** Seek Nonrecoverable read errors Annualized Failure Rate (AFR) Warranty ST3750640AV ST3500630AV 5-22 Hz: 0.02 inches, Limited displacement, peak to peak 22-350 Hz: 0.50 Gs 350-500 Hz: 0.25 Gs 5-350 Hz: 5.0 Gs 350-500 Hz: 1.0 Gs 2.8 (typical) 2.9 (max) 3.2 (typical) 3.4 (max) 1 per 1014 bits read 0.80% To determine the warranty for a specific drive, use a web browser to access the following web page: www.seagate.com/support/service/ Contact start-stop cycles From this page, click on the "Verify Your Warranty" link. You will be asked to provide the drive serial number, model number (or part number) and country of purchase. The system will display the warranty information for your drive. 50,000 at 25°C, 50% rel. humidity *One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting. **During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and power to operational levels. SV35.2 Series PATA Product Manual, Rev. E 5

Section	Page
1.0 Introduction	7
2.0 Drive specifications	9
2.1 Specification summary table	9
2.2 Formatted capacity	14
2.2.1 LBA mode	14
2.3 Default logical geometry	14
2.4 Recording and interface technology	15
2.5 Physical characteristics	15
2.6 Seek time	16
2.7 Start/stop times	16
2.8 Power specifications	16
2.8.1 Power consumption	16
2.8.1.1 Typical current profile	18
2.8.2 Conducted noise	18
2.8.3 Voltage tolerance	18
2.8.4 Power management modes	19
2.9 Environmental specifications	20
2.9.1 Ambient temperature	20
2.9.2 Temperature gradient	20
2.9.3 Humidity	20
2.9.3.1 Relative humidity	20
2.9.3.2 Wet bulb temperature	20
2.9.4 Altitude	20
2.9.5 Shock	21
2.9.5.1 Operating shock	21
2.9.5.2 Nonoperating shock	21
2.9.6 Vibration	21
2.9.6.1 Operating vibration	21
2.9.6.2 Nonoperating vibration	21
2.10 Acoustics	22
2.11 Electromagnetic immunity	22
2.12 Reliability	23
2.12.1 Annualized Failure Rate (AFR) and Mean Time Between Failures (MTBF)	23
2.13 Agency certification	23
2.13.1 Safety certification	23
2.13.2 Electromagnetic compatibility	23
2.13.3 FCC verification	24
2.14 Environmental protection	24
2.14.1 European Union Restriction of Hazardous Substances (RoHS)	25
2.15 Corrosive environment	25
3.0 Configuring and mounting the drive	27
3.1 Handling and static discharge precautions	27
3.2 Breather filter hole precautions	28
3.3 Jumper settings	29
3.3.1 Master/slave configuration	29
3.3.2 Cable-select option	29
3.3.3 Ultra ATA/100 cable	30
3.4 Drive mounting	30
4.0 ATA interface	33
4.1 ATA interface signals and connector pins	33
4.1.1 Supported ATA commands	34
4.1.2 Identify Device command	36
4.1.3 Set Features command	39
4.1.4 S.M.A.R.T. commands	40
5.0 Seagate Technology support services	41
Index	43
A	43
B	43
C	43
D	43
E	43
F	43
G	43
H	43
I	43
J	44
K	44
L	44
M	44
N	44
O	44
P	44
R	44
S	44
T	45
U	45
V	45