Seagate ST300MM0026 Savvio 10K.4 FC Product Manual - Page 59
Inquiry data, Mode Sense data
View all Seagate ST300MM0026 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 59 highlights
9.3.1 Inquiry data Table 16 lists the Inquiry command data that the drive should return to the initiator per the format given in the Fibre Channel Interface Manual. Table 16: Bytes 0-15 16-31 32-47 48-63 64-79 80-95 96-111 112-127 128-143 Savvio 10K.4 FC inquiry data Data (hex) 00 00 xx** 12 8B 00 PP 02 53 45 41 47 41 [53 54 39 36 30 30 32 30 34 46 43]1 20 20 R# R# R# R# S# S# S# S# S# S# S# S# 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 43 6F 70 79 72 69 67 68 74 20 28 63 30* 30* 39* 20 53 65 61 67 61 74 65 20 41 72 69 67 68 74 73 20 72 65 73 65 72 76 54 45 20 Vendor ID 20 20 20 Product ID 00 00 00 00 00 00 00 00 00 00 00 00 29 20 32* *Copyright 6C 6C 20 notice 65 64 20 * Copyright year (changes with actual year). ** SCSI Revision support. Refer to the appropiate SPC release documentation for definitions. PP 50 = Inquiry data for an Inquiry command received on Port A. 70 = Inquiry data for an Inquiry command received on Port B. R# Four ASCII digits representing the last four digits of the product firmware release number. S# Eight ASCII digits representing the eight digits of the product serial number. [ ] Bytes 16 through 26 reflect model of drive. The table above shows the hex values for model ST9600204FC. Bytes 16 through 26 values for other models are shown below: ST9450404FC 53 54 39 34 35 30 34 30 34 46 43 ST9600204FC 53 54 39 36 30 30 32 30 34 46 43 9.3.2 Mode Sense data The Mode Sense command provides a way for the drive to report its operating parameters to the initiator. The drive maintains four sets of mode parameters: 1. Default values Default values are hard-coded in the drive firmware stored in flash E-PROM (nonvolatile memory) on the drive's PCB. These default values can be changed only by downloading a complete set of new firmware into the flash E-PROM. An initiator can request and receive from the drive a list of default values and use those in a Mode Select command to set up new current and saved values, where the values are changeable. 2. Saved values Saved values are stored on the drive's media using a Mode Select command. Only parameter values that are allowed to be changed can be changed by this method. Parameters in the saved values list that are not changeable by the Mode Select command get their values from default values storage. When power is applied to the drive, it takes saved values from the media and stores them as current values in volatile memory. It is not possible to change the current values (or the saved values) with a Mode Select command before the drive achieves operating speed and is "ready." An attempt to do so results in a "Check Condition" status. On drives requiring unique saved values, the required unique saved values are stored into the saved values storage location on the media prior to shipping the drive. Some drives may have unique firmware with unique default values also. Savvio 10K.4 FC Product Manual, Rev. A 53