Seagate ST3100011A Barracuda 7200.7 PATA Install Guide - Page 2

BIOS Settings Drive Model Formatted Gbytes Total Sectors* ST3200822A 200.0 390,721,968 ST3200821A 200.0 390,721,968 ST3160023A 160.0 312,581,808 ST3160021A 160.0 312,581,808 ST3120026A 120.0 234,441,648 ST3120022A 120.0 234,441,648 ST380013A 80.0 156,301,488 ST380011A 80.0 156,301,488 ST340014A 40.0 78,165,360 *One sector equals 512 bytes. Cache 8 Mbytes 2 Mbytes 8 Mbytes 2 Mbytes 8 Mbytes 2 Mbytes 8 Mbytes 2 Mbytes 2 Mbytes Preparing the drive using DiscWizard Installing a single drive If you are installing a single drive, we recommend using DiscWizard to automatically partition and format your drive. DiscWizard software is available at www.seagate.com and is free. During the download, the Diskette Creator creates a portable bootable diskette. To run DiscWizard: 1. Insert your bootable DiscWizard diskette and follow the instructions. DiscWizard will guide you through the installation process. 2. Boot your computer from the Windows operating system CD-ROM or from your system startup diskette with the Windows CD loaded. At the prompt, type setup. Follow the instructions provided on your screen. Installing a slave drive If you are installing a second drive, or slave, to your system, use the DiscWizard software available at www.seagate.com. If you do not want to install your drive using either DiscWizard or Disk Manager, see "Standard Microsoft Installation" below to partition and format your drive. Standard Microsoft installation Caution. Partitioning or formatting a drive erases all data on the drive. Seagate assumes no liability if you erase your data. 1. Insert a bootable Windows startup diskette and restart your computer. This is provided with your Microsoft Windows operating system software. 2. Run fdisk and create a primary DOS partition. 3. Mark the partition as active to make the partition bootable. Drive formatting Caution. Use the correct drive letters to prevent formatting a drive that already contains data. 1. At the A: prompt, type format x: (where x is the letter of your first new partition) and then press the Enter key. Repeat the format process for all new partitions. 2. Proceed to "Loading the operating system" below. Loading the operating system Note. The operating system needs to be installed on the master drive only. It is not required when adding a second drive. 1. Boot your computer from your Windows operating system CD-ROM or from your system startup diskette with the Windows CD loaded in the CD drive. 2. At the prompt, type setup and continue with the Windows setup as instructed on your screen. Troubleshooting If your drive is not working properly, these troubleshooting tips may help solve the problem. 1. Does the drive spin up? A spinning drive produces a faint whine and clicking noise that begins when power is applied. If your drive does not spin, check that the power connector and interface cable are securely attached and the jumpers are installed correctly. 2. Does the computer recognize the drive? Verify that the drive is enabled in the system CMOS or setup program. If not, select the autodetect option and enable it. If your drive has a problem, it may not be recognized by the system. 3. Does FDISK detect the drive? Run the FDISK program located on your Windows startup diskette. Type fdisk/status to verify that your hard drive is present and recognized by the system. 4. Does Scandisk find the drive defect-free? Scandisk is a utility located on your Windows startup diskette that scans the drive for defects. If defects are detected, this may be an indication of a problem. 5. Why won't the drive format to full capacity? Verify that your BIOS has autodetect and LBA mode enabled. Otherwise, you may need to use Disk Manager to achieve the full capacity of your drive. Download the latest version from www.seagate.com or find it on your CD. 6. Why does my computer hang on startup? Verify that your system is ATA/100 compatible with the UDMA mode setting. Some legacy BIOS cause hangs on startup or other problems if it is not ATA/100 compatible. For more information, see the earlier section on the Ultra ATA/100 requirements. In addition, some legacy BIOS may cause a hang due to the large drive capacity. Consider using the alternate capacity jumper if it is available on your drive model. Use the alternate capacity jumper if your computer does not support higher capacity drives. The jumper will limit large capacity drives to 32 Gbytes. Note. If these tips do not answer your question or solve the problem, contact your dealer or visit http://seatools.seagate.com to download SeaTools disc diagnostics software and more troubleshooting advice. Seagate support services For online information about Seagate products, visit www.seagate.com or e-mail your disc questions to [email protected]. If you need help installing your drive, consult your dealer first. If you need additional help, call a Seagate technical support specialist. Before calling, note your system configuration and drive model number. Africa +1-405-324-4714 Australia 1800-14-7201 Austria 0 800-20 12 90 Belgium 00 800-47324283 China* 800-810-9668 Denmark 00 800-47324283 France 00 800-47324283 Germany 00 800-47324283 Hong Kong 800-90-0474 Hong Kong† 001-800-0830-1730 India 1-600-33-1104 Indonesia 001-803-1-003-2165 Ireland 00 800-47324283 Italy 00 800-47324283 Japan 0034 800 400 554 Malaysia 1-800-80-2335 Middle East +1-405-324-4714 Netherlands 00 800-47324283 New Zealand 0800-443988 Norway 00 800-47324283 Poland 00 800-311 12 38 Spain 00 800-47324283 Sweden 00 800-47324283 Switzerland 00 800-47324283 Singapore 800-1101-150 Taiwan* 00-800-0830-1730 Thailand 001-800-11-0032165 Turkey 00 800-31 92 91 40 United Kingdom 00 800-47324283 USA/Canada/ 1-800 SEAGATE or Latin America +1-405-324-4700 Other European countries +1-405-324-4714 *Mandarin †Cantonese Warranty. To determine the warranty status of your Seagate disc drive, contact your place of purchase or visit our web site at www.seagate.com for more information. Return Merchandise Authorization (RMA). Run SeaTools to diagnose your drive before requesting a return authorization. In addition, please verify that your drive is defective by following the troubleshooting checklist in this guide. Seagate offers comprehensive customer support for all Seagate drives worldwide. Seagate customer service centers are the only facilities authorized to service Seagate drives. Drive return procedures vary depending on geographical location and are subject to current international trade regulations. Shipping the drive Caution. Back up the data before shipping. Seagate assumes no responsibility for data lost during shipping or service. Shipping drive in an unapproved container voids the warranty. Pack the drive with original box and packing materials. Use no other materials. This prevents electrical and physical damage in transit. Electromagnetic compliance for the European Union. This model complies with the European Union requirements of the Electromagnetic Compatibility Directive 89/ 336/EEC of 03 May 1989 as amended by Directive 92/31/EEC of 28 April 1992 and Directive 93/68/EEC of 22 July 1993. Compliance of this drive, as a system component, was confirmed with a test system. We cannot guarantee that your system will comply. The drive is not meant for external use (without properly designed enclosure, shielded I/O cable, etc.). Sicherheitsanleitung 1. Das Gerrät ist ein Einbaugerät, das für eine maximale Umgebungstempeatur von 60°C vorgesehen ist. 2. Zur Befestigung des Lufwerks werden 4 Schrauben 6-32 UNC-2A benötigt. Bei seitlicher Befestigung darf die maximale Länge der Schrauben im Chassis nicht merh als 3,3 mm und bei Befestigung an der Unterseite nicht mehr als 5,08 mm betragen. 3. Als Versorgungsspannugen werden benötigt: +5V +/- 5% 1,2A; +12V +/- 5% 2,0A 4. Die Versorgungsspannung muss SELV entsprechen. 5. Alle Arbeiten auf dem Festplattte dürfen nur von Ausgebiletem Serciepersonal durchgeführt werden. Bitte entfernen Sie nicht die Aufschriftenschilder des Laufwerkes. 6. Der Einbau des Laufwerkes muss den Anforderungen gemäss DIN IEC 950 VDE 0805/05.90 entspreche. © 2003, 2004 Seagate Technology LLC. All rights reserved Publication number: 100217284, Rev. D, March 2004, Printed in USA Seagate and Seagate Technology are registered trademarks of Seagate Technology LLC. Barracuda and the Wave logo are either registered trademark or trademarks of Seagate Technology LLC. Other product names are registered trademarks or trademarks of their owners. Seagate reserves the right to change, without notice, product offerings or specifications.