Seagate ST3146707LW Cheetah 10K.7 SCSI Product Manual - Page 68

Table 6 lists the Standard Inquiry command data that the drive should return to the initiator per the format given in the SCSI Interface Product Manual, part number 75789509, Inquiry command section. Table 6: Cheetah 10K.7 SCSI family drive Standard Inquiry data Bytes Data (HEX) 0-15 16-31 00 00 [03]1 [12]2 8B 00 01 3E 53 45 41 47 41 54 45 20 VENDOR ID 53 54 [33] [33] [30] [30] [30] [30] [37] [4C] [57]3 20 20 20 20 20 PRODUCT ID 32-47 R# R# R# R# S# S# S# S# S# S# S# S# 00 00 00 00 48-63 00 00 00 00 00 00 00 00 0F 00 00 00 00 00 00 00 64-79 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80-95 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 96-111 00 43 6F 70 79 72 69 67 68 74 20 28 63 29 20 [Y] COPYRIGHT 112-127 [y] [y] [y]4 20 53 65 61 67 61 74 65 20 41 6C 6C 20 NOTICE 128-143 72 69 67 68 74 73 20 72 65 73 65 72 76 65 64 20 [ ]1 03 means SCSI-3 (Ultra160) implemented. Note. Seagate has chosen to set this bit to 03, SCSI-3 (Ultra160) implemented, rather than 04, SCSI-4 (Ultra320) implemented, due to compatibility issues with some host bus adapters. This setting will not affect the Ultra320 functionality of the drive. [ ]2 The drive can be changed between these two configurations: 02 means response data in SCSI-2/SCSI-3 format. 12 means the drive uses the hierarchical addressing mode to assign LUNs to logical units (default is 12). R# Four ASCII digits representing the last four digits of the product Firmware Release number. This information is also given in the Vital Product Data page C0h, together with servo RAM and ROM release numbers. S# Eight ASCII digits representing the eight digits of the product serial number. [ ]3 Bytes 18 through 26 reflect model of drive. The table above shows the hex values for Model ST3300007LW. Refer to the values below for the values of bytes 18 through 26 of you particular model: ST3300007LW 33 33 30 30 30 30 37 4C 57 ST3300007LC 33 33 30 30 30 30 37 4C 43 ST3146707LW 33 31 34 36 37 30 37 4C 57 ST3146707LC 33 31 34 36 37 30 37 4C 43 ST373207LW 33 37 33 32 30 37 4C 57 20 ST373207LC 33 37 33 32 30 37 4C 43 20 [ ]4 Copyright Year - the year the drive's firmware code was built. 9.3.1 Inquiry Vital Product data Instead of the standard Inquiry data shown in Table 6, the initiator can request several Vital Product Data pages by setting the Inquiry command EVPD bit to one. The SCSI Interface Product Manual lists the Vital Product Data pages and describes their formats. A separate Inquiry command must be sent to the drive for each Vital Product Data page the initiator wants the drive to send back. 58 Cheetah 10K.7 SCSI Product Manual, Rev. D