Home » Seagate Manuals » Hard Drives » Seagate ST3160215A » Manual Viewer

Seagate ST3160215A Barracuda 7200.10 PATA Product Manual - Page 25

Drive specification, ST340815A, ST340215A - hard drive

UPC - 890552659074

Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

Drive specification Vibration, operating Vibration, nonoperating Drive acoustics, sound power (bels) Idle** Quiet seek Nonrecoverable read errors Annualized Failure Rate (AFR) Warranty Contact start-stop cycles (25°C, 50% rel. humidity) ST340815A ST340215A 5-22 Hz: 0.25 Gs, Limited displacement 22-350 Hz: 0.50 Gs 350-500 Hz:: 0.25 Gs 5-22 Hz: 0.25 Gs, Limited displacement 22-350 Hz: 5.0 Gs 350-500 Hz:: 1.0 Gs 2.8 (typical) 3.0 (max) 3.0 (typical) 3.2 (max) 1 per 1014 bits read 0.34% 5 years on distribution units. To determine the warranty for a specific drive, use a web browser to access the following web page: www.seagate.com/support/service/ From this page, click on the "Verify Your Warranty" link. You will be asked to provide the drive serial number, model number (or part number) and country of purchase. The system will display the warranty information for your drive. 50,000 *One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting. **During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and power to operational levels. Barracuda 7200.10 PATA Product Manual, Rev. F 19

Section	Page
1.0 Introduction	7
2.0 Drive specifications	9
2.1 Specification summary table	9
2.2 Formatted capacity	26
2.2.1 LBA mode	26
2.3 Default logical geometry	26
2.4 Recording and interface technology	27
2.5 Physical characteristics	27
2.6 Seek time	28
2.7 Start/stop times	28
2.8 Power specifications	28
2.8.1 Power consumption	28
2.8.1.1 Typical current profile	30
2.8.2 Conducted noise	30
2.8.3 Voltage tolerance	31
2.8.4 Power management modes	31
2.9 Environmental specifications	32
2.9.1 Ambient temperature	32
2.9.2 Temperature gradient	32
2.9.3 Humidity	32
2.9.3.1 Relative humidity	32
2.9.3.2 Wet bulb temperature	32
2.9.4 Altitude	32
2.9.5 Shock	33
2.9.5.1 Operating shock	33
2.9.5.2 Nonoperating shock	33
2.9.6 Vibration	33
2.9.6.1 Operating vibration	33
2.9.6.2 Nonoperating vibration	33
2.10 Acoustics	34
2.11 Electromagnetic immunity	35
2.12 Reliability	36
2.12.1 Annualized Failure Rate (AFR) and Mean Time Between Failures (MTBF)	36
2.13 Agency certification	36
2.13.1 Safety certification	36
2.13.2 Electromagnetic compatibility	36
2.13.3 FCC verification	37
2.14 Environmental protection	37
2.14.1 European Union Restriction of Hazardous Substances (RoHS)	38
2.15 Corrosive environment	38
3.0 Configuring and mounting the drive	39
3.1 Handling and static discharge precautions	39
3.2 Breather filter hole precautions	40
3.3 Jumper settings	41
3.3.1 Master/slave configuration	41
3.3.2 Cable-select option	41
3.3.3 Ultra ATA/100 cable	42
3.4 Drive mounting	42
4.0 ATA interface	45
4.1 ATA interface signals and connector pins	45
4.1.1 Supported ATA commands	46
4.1.2 Identify Device command	48
4.1.3 Set Features command	51
4.1.4 S.M.A.R.T. commands	52
5.0 Seagate Technology support services	53
A	55
B	55
C	55
D	55
E	55
F	55
G	55
H	55
I	55
J	56
K	56
L	56
M	56
N	56
O	56
P	56
R	56
S	56
T	57
U	57
V	57