Seagate ST450MP0074 Savvio 15K.3 SAS Product Manual - Page 62
Inquiry data, Table 8, Savvio inquiry data, Mode Sense data
View all Seagate ST450MP0074 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 62 highlights
12.3.1 Inquiry data Table 8 lists the Inquiry command data that the drive should return to the initiator per the format given in the SAS Interface Manual. Table 8: Savvio inquiry data Bytes Data (hex) 0-15 00 00 03** 12 8B 00 PP 0A 53 45 41 47 41 54 45 20 Vendor ID 16-31 32-47 [53 54 39 33 30 30 36 35 33 53 53] 20 20 20 20 20 Product ID R# R# R# R# S# S# S# S# S# S# S# S# 00 00 00 00 48-63 64-79 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80-95 96-111 00 00 00 00 43 6F 00 00 00 00 00 00 00 00 70 79 72 69 67 68 74 20 00 00 00 00 00 28 63 29 20 32* *Copyright 112-127 128-143 30* 31* 30* 20 53 65 61 67 61 74 65 72 69 67 68 74 73 20 72 65 73 65 20 41 6C 6C 20 notice 72 76 65 64 20 * Copyright year (changes with actual year). ** SCSI Revision support. See the appropriate SPC release documentation for definitions. PP 10 = Inquiry data for an Inquiry command received on Port A. 30 = Inquiry data for an Inquiry command received on Port B. R# Four ASCII digits representing the last four digits of the product firmware release number. S# Eight ASCII digits representing the eight digits of the product serial number. [ ] Bytes 16 through 26 reflect model of drive. The table above shows the hex values for Model ST9300653SS. Refer to the values below for the values of bytes 16 through 26 of your particular model: ST9300553SS 53 54 39 33 30 30 35 35 33 53 53 ST9300453SS 53 54 39 33 30 30 34 35 33 53 53 ST9146853SS 53 54 39 31 34 36 38 35 33 53 53 ST9146753SS 53 54 39 31 34 36 37 35 33 53 53 ST9146653SS 53 54 39 31 34 36 36 35 33 53 53 12.3.2 Mode Sense data The Mode Sense command provides a way for the drive to report its operating parameters to the initiator. The drive maintains four sets of mode parameters: 1. Default values Default values are hard-coded in the drive firmware stored in flash E-PROM (nonvolatile memory) on the drive's PCB. These default values can be changed only by downloading a complete set of new firmware into the flash E-PROM. An initiator can request and receive from the drive a list of default values and use those in a Mode Select command to set up new current and saved values, where the values are changeable. 2. Saved values Saved values are stored on the drive's media using a Mode Select command. Only parameter values that are allowed to be changed can be changed by this method. Parameters in the saved values list that are not changeable by the Mode Select command get their values from default values storage. When power is applied to the drive, it takes saved values from the media and stores them as current values in volatile memory. It is not possible to change the current values (or the saved values) with a Mode 54 Savvio 15K.3 SAS Product Manual, Rev. E