Home » Seagate Manuals » Hard Drives » Seagate ST500DM002 » Manual Viewer

Seagate ST500DM002 Barracuda 7200.11 SATA Product Manual - Page 22

Vibration, 8.6.1, Operating vibration, 8.6.2, Nonoperating vibration, GB, 750 GB and 500 GB models

Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

2.8.6 Vibration All vibration specifications assume that the drive is mounted securely with the input vibration applied at the drive mounting screws. Vibration may be applied in the X, Y or Z axis. 2.8.6.1 Operating vibration The maximum vibration levels that the drive may experience while meeting the performance standards specified in this document are specified below. 2-22 Hz 22-350 Hz 350-500 Hz 0.25 Gs (Limited displacement) 0.50 Gs 0.25 Gs 2.8.6.2 Nonoperating vibration The maximum nonoperating vibration levels that the drive may experience without incurring physical damage or degradation in performance when subsequently put into operation are specified below. 1000 GB, 750 GB and 500 GB models 5-22 Hz 22-350 Hz 350-500 Hz 2.0 Gs (limited displacement) 5.0 Gs 2.0 Gs 16 Barracuda 7200.11 Serial ATA Product Manual, Rev. G

Section	Page
1.0 Introduction 1	3
1.1 About the Serial ATA interface 2	3
2.0 Drive specifications 3	3
2.1 Formatted capacity 10	3
2.1.1 LBA mode 10	3
2.2 Default logical geometry 10	3
2.3 Recording and interface technology 10	3
2.4 Physical characteristics 11	3
2.5 Seek time 11	3
2.6 Start/stop times 11	3
2.7 Power specifications 12	3
2.7.1 Power consumption 12	3
2.7.2 Conducted noise 14	3
2.7.3 Voltage tolerance 14	3
2.7.4 Power-management modes 14	3
2.8 Environmental specifications 15	3
2.8.1 Ambient temperature 15	3
2.8.2 Temperature gradient 15	3
2.8.3 Humidity 15	3
2.8.4 Altitude 15	3
2.8.5 Shock 15	3
2.8.6 Vibration 16	3
2.9 Acoustics 17	3
2.9.1 Test for Prominent Discrete Tones (PDTs) 17	3
2.10 Electromagnetic immunity 17	3
2.11 Reliability 18	3
2.11.1 Annualized Failure Rate (AFR) and Mean Time Between Failures (MTBF) 18	3
2.12 Agency certification 18	3
2.12.1 Safety certification 18	3
2.12.2 Electromagnetic compatibility 18	3
2.12.3 FCC verification 19	3
2.13 Environmental protection 20	3
2.13.1 European Union Restriction of Hazardous Substances (RoHS) Directive 20	3
2.14 Corrosive environment 20	3
3.0 Configuring and mounting the drive 21	3
3.1 Handling and static-discharge precautions 21	3
3.2 Configuring the drive 22	3
3.3 Serial ATA cables and connectors 22	3
3.4 Drive mounting 23	3
4.0 Serial ATA (SATA) interface 25	3
4.1 Hot-Plug compatibility 25	3
4.2 Serial ATA device plug connector pin definitions 26	3
4.3 Supported ATA commands 27	3
4.3.1 Identify Device command 29	3
4.3.2 Set Features command 33	3
4.3.3 S.M.A.R.T. commands 34	3
5.0 Seagate Technology support services 35	3
Figure 1. Typical 5V startup and operation current profile 13	5
Figure 2. Typical 12V startup and operation current profile 13	5
Figure 3. Serial ATA connectors 22	5
Figure 4. Attaching SATA cabling 22	5
Figure 5. Mounting dimensions 23	5
1.0 Introduction	7
1.1 About the Serial ATA interface	8
2.0 Drive specifications	9
2.1 Formatted capacity	16
2.1.1 LBA mode	16
2.2 Default logical geometry	16
2.3 Recording and interface technology	16
2.4 Physical characteristics	17
2.5 Seek time	17
2.6 Start/stop times	17
2.7 Power specifications	18
2.7.1 Power consumption	18
2.7.1.1 Typical current profiles	19
2.7.2 Conducted noise	20
2.7.3 Voltage tolerance	20
2.7.4 Power-management modes	20
2.8 Environmental specifications	21
2.8.1 Ambient temperature	21
2.8.2 Temperature gradient	21
2.8.3 Humidity	21
2.8.3.1 Relative humidity	21
2.8.3.2 Wet bulb temperature	21
2.8.4 Altitude	21
2.8.5 Shock	21
2.8.5.1 Operating shock	21
2.8.5.2 Nonoperating shock	21
2.8.6 Vibration	22
2.8.6.1 Operating vibration	22
2.8.6.2 Nonoperating vibration	22
2.9 Acoustics	23
2.9.1 Test for Prominent Discrete Tones (PDTs)	23
2.10 Electromagnetic immunity	23
2.11 Reliability	24
2.11.1 Annualized Failure Rate (AFR) and Mean Time Between Failures (MTBF)	24
2.12 Agency certification	24
2.12.1 Safety certification	24
2.12.2 Electromagnetic compatibility	24
2.12.3 FCC verification	25
2.13 Environmental protection	26
2.13.1 European Union Restriction of Hazardous Substances (RoHS) Directive	26
2.14 Corrosive environment	26
3.0 Configuring and mounting the drive	27
3.1 Handling and static-discharge precautions	27
3.2 Configuring the drive	28
3.3 Serial ATA cables and connectors	28
3.4 Drive mounting	29
4.0 Serial ATA (SATA) interface	31
4.1 Hot-Plug compatibility	31
4.2 Serial ATA device plug connector pin definitions	32
4.3 Supported ATA commands	33
4.3.1 Identify Device command	35
4.3.2 Set Features command	39
4.3.3 S.M.A.R.T. commands	40
5.0 Seagate Technology support services	41
Index	43
A	43
B	43
C	43
D	43
E	43
F	43
G	43
H	43
I	44
K	44
L	44
M	44
N	44
O	44
P	44
Q	44
R	44
S	45
T	45
U	45
V	45