Home » Seagate Manuals » Hard Drives » Seagate ST500DM002 » Manual Viewer

Seagate ST500DM002 Barracuda 7200.10 PATA Product Manual - Page 41

Jumper settings - jumpers

Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

3.3 Jumper settings 3.3.1 Master/slave configuration The options jumper block shown in Figure 4 is used to configure the drive for operation. It is the 8-pin dual header between the interface connector and the power connector. Use the following settings to configure the drive as a master or a slave. Master or single drive. The drive is configured at the factory for a master or single drive operation with a jumper set on pins 7 and 8. Drive as slave. Remove all jumpers. Drive as master with a non-ATA-compatible slave. Use this jumper setting only if the drive does not work as a master with no jumpers installed. Options jumper block *Master or single drive Drive is slave Master with non ATAcompatible slave *Cable select 7531 8642 Figure 4 Master/slave jumper settings 3.3.2 Cable-select option Computers that use cable select determine the master and slave drives by selecting or deselecting pin 28, CSEL, on the interface bus. Master and slave drives are determined by their physical position on the cable. To enable cable select, set a jumper on pins 5 and 6 as shown in Figure 4. Refer to your computer manual to determine whether your computer supports this option. Barracuda 7200.10 PATA Product Manual, Rev. F 35

Section	Page
1.0 Introduction	7
2.0 Drive specifications	9
2.1 Specification summary table	9
2.2 Formatted capacity	26
2.2.1 LBA mode	26
2.3 Default logical geometry	26
2.4 Recording and interface technology	27
2.5 Physical characteristics	27
2.6 Seek time	28
2.7 Start/stop times	28
2.8 Power specifications	28
2.8.1 Power consumption	28
2.8.1.1 Typical current profile	30
2.8.2 Conducted noise	30
2.8.3 Voltage tolerance	31
2.8.4 Power management modes	31
2.9 Environmental specifications	32
2.9.1 Ambient temperature	32
2.9.2 Temperature gradient	32
2.9.3 Humidity	32
2.9.3.1 Relative humidity	32
2.9.3.2 Wet bulb temperature	32
2.9.4 Altitude	32
2.9.5 Shock	33
2.9.5.1 Operating shock	33
2.9.5.2 Nonoperating shock	33
2.9.6 Vibration	33
2.9.6.1 Operating vibration	33
2.9.6.2 Nonoperating vibration	33
2.10 Acoustics	34
2.11 Electromagnetic immunity	35
2.12 Reliability	36
2.12.1 Annualized Failure Rate (AFR) and Mean Time Between Failures (MTBF)	36
2.13 Agency certification	36
2.13.1 Safety certification	36
2.13.2 Electromagnetic compatibility	36
2.13.3 FCC verification	37
2.14 Environmental protection	37
2.14.1 European Union Restriction of Hazardous Substances (RoHS)	38
2.15 Corrosive environment	38
3.0 Configuring and mounting the drive	39
3.1 Handling and static discharge precautions	39
3.2 Breather filter hole precautions	40
3.3 Jumper settings	41
3.3.1 Master/slave configuration	41
3.3.2 Cable-select option	41
3.3.3 Ultra ATA/100 cable	42
3.4 Drive mounting	42
4.0 ATA interface	45
4.1 ATA interface signals and connector pins	45
4.1.1 Supported ATA commands	46
4.1.2 Identify Device command	48
4.1.3 Set Features command	51
4.1.4 S.M.A.R.T. commands	52
5.0 Seagate Technology support services	53
A	55
B	55
C	55
D	55
E	55
F	55
G	55
H	55
I	55
J	56
K	56
L	56
M	56
N	56
O	56
P	56
R	56
S	56
T	57
U	57
V	57