Seagate ST9450204SS Savvio 10K.4 SAS Product Manual - Page 63
Inquiry data, Table 8, Savvio inquiry data, Mode Sense data
View all Seagate ST9450204SS manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 63 highlights
10.3.1 Inquiry data Table 8 lists the Inquiry command data that the drive should return to the initiator per the format given in the SAS Interface Manual. Table 8: Bytes 0-15 16-31 32-47 48-63 64-79 80-95 96-111 112-127 128-143 Savvio inquiry data Data (hex) 00 00 xx** 12 8B 01 PP 02 53 45 41 47 41 54 45 20 Vendor ID [53 54 39 36 30 30 32 30 34 53 53] 20 20 20 20 20 Product ID R# R# R# R# S# S# S# S# S# S# S# S# 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 43 6F 70 79 72 69 67 68 74 20 28 63 29 20 32* *Copyright 30* 30* 39* 20 53 65 61 67 61 74 65 20 41 6C 6C 20 notice 72 69 67 68 74 73 20 72 65 73 65 72 76 65 64 20 * Copyright year (changes with actual year). ** SCSI Revision support. See the appropriate SPC release documention for definitions. PP 10 = Inquiry data for an Inquiry command received on Port A. 30 = Inquiry data for an Inquiry command received on Port B. R# Four ASCII digits representing the last four digits of the product firmware release number. S# Eight ASCII digits representing the eight digits of the product serial number. [ ] Bytes 16 through 26 reflect model of drive. The table above shows the hex values for Model ST9600204SS. Refer to the values below for the values of bytes 16 through 26 of you particular model: ST9600204SS ST9600104SS ST9450404SS ST9450304SS 53 54 39 36 30 30 32 30 34 53 53 53 54 39 36 30 30 31 30 34 53 53 53 54 39 34 35 30 34 30 34 53 53 53 54 39 34 35 30 33 30 34 53 53 10.3.2 Mode Sense data The Mode Sense command provides a way for the drive to report its operating parameters to the initiator. The drive maintains four sets of mode parameters: 1. Default values Default values are hard-coded in the drive firmware stored in flash E-PROM (nonvolatile memory) on the drive's PCB. These default values can be changed only by downloading a complete set of new firmware into the flash E-PROM. An initiator can request and receive from the drive a list of default values and use those in a Mode Select command to set up new current and saved values, where the values are changeable. 2. Saved values Saved values are stored on the drive's media using a Mode Select command. Only parameter values that are allowed to be changed can be changed by this method. Parameters in the saved values list that are not changeable by the Mode Select command get their values from default values storage. When power is applied to the drive, it takes saved values from the media and stores them as current values in volatile memory. It is not possible to change the current values (or the saved values) with a Mode Select command before the drive achieves operating speed and is "ready." An attempt to do so results in a "Check Condition" status. Savvio 10K.4 SAS Product Manual, Rev. C 55