Seagate ST9500327AS Momentus 5400 FDE.4 SATA Product Manual - Page 21

Momentus 5400 FDE.4 SATA Product Manual, Rev. B

15

2.13

Reliability

Measurement type

Specification

Nonrecoverable read errors

1 per 10

14

bits read, max.

Annualized Failure Rate (AFR)

<0.48%

Load/Unload (U/UL)

25°C, 50% relative humidity





600,000 software-controlled power on/off cycles

20,000 hard power on/off cycles

600,000 software-controlled power on/off cycles

20,000 hard power on/off cycles

Warranty

To determine the warranty for a specific drive, use a web browser to access the

following web page:

support.seagate.com/customer/warranty_validation.jsp

You will be asked to provide the drive serial number, model number (or part num-

ber) and country of purchase. After submitting this information, the system will dis-

play the warranty information for your drive.

2.14

Agency certification

2.14.1

Safety certification

The drives are recognized in accordance with UL 60950-1 and CSA C22.2 (60950) and meet all applicable

sections of IEC950 and EN 60950 as tested by UL Singapore and TUV SUD PSB Singapore.

2.14.2

Electromagnetic compatibility

Hard drives that display the CE mark comply with the European Union (EU) requirements specified in the Elec-

tromagnetic Compatibility Directive (2004/108/EEC). Testing is performed to the levels specified by the product

standards for Information Technology Equipment (ITE). Emission levels are defined by EN 55022, Class B and

the immunity levels are defined by EN 55024.

Seagate uses an independent laboratory to confirm compliance with the EC directives specified in the previous

paragraph. Drives are tested in representative end-user systems. Although CE-marked Seagate drives comply

with the directives when used in the test systems, we cannot guarantee that all systems will comply with the

directives. The drive is designed for operation inside a properly designed enclosure, with properly shielded I/O

cable (if necessary) and terminators on all unused I/O ports. Computer manufacturers and system integrators

should confirm EMC compliance and provide CE marking for their products.

Section	Page
1.0 Introduction 1	3
1.1 System requirements 1	3
1.2 About Momentus 5400 FDE.4 SATA disk drives 2	3
1.2.1 Drive state upon shipment 3	3
2.0 Drive specifications 4	3
2.1 Specification summary table 4	3
2.2 Formatted capacity 6	3
2.2.1 LBA mode 6	3
2.3 Default logical geometry 6	3
2.4 Physical organization 7	3
2.5 Recording and interface technology 7	3
2.6 Physical characteristics 7	3
2.7 Seek time 8	3
2.8 Start/stop times 8	3
2.9 Power specifications 9	3
2.9.1 Power consumption 9	3
2.9.2 Deferred spinup 10	3
2.9.3 Conducted noise 10	3
2.9.4 Voltage tolerance 10	3
2.9.5 Power-management modes 11	3
2.10 Environmental specifications 12	3
2.10.1 Ambient temperature 12	3
2.10.2 Temperature gradient 12	3
2.10.3 Humidity 12	3
2.10.4 Altitude 12	3
2.10.5 Shock 13	3
2.10.6 Vibration 13	3
2.11 Acoustics 14	3
2.12 Electromagnetic immunity 14	3
2.13 Reliability 15	3
2.14 Agency certification 15	3
2.14.1 Safety certification 15	3
2.14.2 Electromagnetic compatibility 15	3
2.14.3 FCC verification 16	3
2.15 Environmental protection 17	3
2.15.1 European Union Restriction of Hazardous Substances (RoHS) 17	3
2.15.2 China Restriction of Hazardous Substances (RoHS) Directive 17	3
2.16 Corrosive environment 17	3
3.0 Configuring and mounting the drive 18	3
3.1 Handling and static-discharge precautions 18	3
3.2 Configuring the drive 19	3
3.3 Serial ATA cables and connectors 19	3
3.4 Drive mounting 20	3
3.5 Drive integration 22	3
3.5.1 Drive installation 23	3
3.5.2 Consumer usage 23	3
3.6 Security Erase--ATA security commands 23	3
3.6.1 Secure Erase procedure 23	3
3.6.2 Drive State after Secure Erase 24	3
4.0 Serial ATA interface 25	3
4.1 Hot-Plug compatibility 25	3
4.2 Serial ATA device plug connector pin definitions 25	4
4.2.1 ATA Security policy exceptions 26	4
4.2.2 DriveTrust Mode support 28	4
4.2.3 Full Disk Encryption support 29	4
4.2.4 Supported ATA commands 30	4
4.2.5 Identify Device command 33	4
4.2.6 Set Features command 36	4
4.2.7 S.M.A.R.T. commands 38	4
5.0 Compatibility summary 39	4
5.1 Installation considerations 39	4
5.2 System Compatibility using WIndows XP SP2 39	4
5.2.1 BIOS versions tested in ATA Security mode 39	4
5.2.2 DriveTrust compatibility verification 42	4
5.3 Operating system versions tested 46	4
5.4 Compatibility test configurations 46	4
6.0 Seagate Technology support services 47	4
Figure 1. Typical +5V only startup and operation current profile 10	5
Figure 2. Serial ATA connectors 19	5
Figure 3. Attaching SATA cabling 19	5
Figure 4. Mounting dimensions 21	5
Figure 5. Momentus 5400 FDE.4 SATA drive label example 22	5
1.0 Introduction	7
1.1 System requirements	7
1.2 About Momentus 5400 FDE.4 SATA disk drives	8
1.2.1 Drive state upon shipment	9
2.0 Drive specifications	10
2.1 Specification summary table	10
2.2 Formatted capacity	12
2.2.1 LBA mode	12
2.3 Default logical geometry	12
2.4 Physical organization	13
2.5 Recording and interface technology	13
2.6 Physical characteristics	13
2.7 Seek time	14
2.8 Start/stop times	14
2.9 Power specifications	15
2.9.1 Power consumption	15
2.9.1.1 Typical current profile	16
2.9.2 Deferred spinup	16
2.9.3 Conducted noise	16
2.9.4 Voltage tolerance	16
2.9.5 Power-management modes	17
2.10 Environmental specifications	18
2.10.1 Ambient temperature	18
2.10.2 Temperature gradient	18
2.10.3 Humidity	18
2.10.3.1 Relative humidity	18
2.10.3.2 Wet bulb temperature	18
2.10.4 Altitude	18
2.10.5 Shock	19
2.10.5.1 Operating shock	19
2.10.5.2 Nonoperating shock	19
2.10.6 Vibration	19
2.10.6.1 Operating vibration	19
2.10.6.2 Nonoperating vibration	19
2.11 Acoustics	20
2.12 Electromagnetic immunity	20
2.13 Reliability	21
2.14 Agency certification	21
2.14.1 Safety certification	21
2.14.2 Electromagnetic compatibility	21
2.14.3 FCC verification	22
2.15 Environmental protection	23
2.15.1 European Union Restriction of Hazardous Substances (RoHS)	23
2.15.2 China Restriction of Hazardous Substances (RoHS) Directive	23
2.16 Corrosive environment	23
3.0 Configuring and mounting the drive	24
3.1 Handling and static-discharge precautions	24
3.2 Configuring the drive	25
3.3 Serial ATA cables and connectors	25
3.4 Drive mounting	26
3.5 Drive integration	28
3.5.1 Drive installation	29
3.5.2 Consumer usage	29
3.6 Security Erase--ATA security commands	29
3.6.1 Secure Erase procedure	29
3.6.2 Drive State after Secure Erase	30
4.0 Serial ATA interface	31
4.1 Hot-Plug compatibility	31
4.2 Serial ATA device plug connector pin definitions	31
4.2.1 ATA Security policy exceptions	32
4.2.2 DriveTrust Mode support	34
4.2.3 Full Disk Encryption support	35
4.2.4 Supported ATA commands	36
4.2.5 Identify Device command	39
4.2.6 Set Features command	42
4.2.7 S.M.A.R.T. commands	44
5.0 Compatibility summary	45
5.1 Installation considerations	45
5.2 System Compatibility using WIndows XP SP2	45
5.2.1 BIOS versions tested in ATA Security mode	45
5.2.2 DriveTrust compatibility verification	48
5.3 Operating system versions tested	52
5.4 Compatibility test configurations	52
6.0 Seagate Technology support services	53
Index	55
A	55
B	55
C	55
D	55
E	55
F	55
G	55
H	55
I	56
K	56
L	56
M	56
N	56
O	56
P	56
Q	56
R	56
S	56
T	57
U	57
V	57

Seagate ST9500327AS Momentus 5400 FDE.4 SATA Product Manual - Page 21

Reliability, Agency certification

Page 21 highlights