Home » Seagate Manuals » Hard Drives » Seagate ST9900805SS » Manual Viewer

Seagate ST9900805SS Savvio 10K.2 SAS Product Manual - Page 69

additional sinusoidal jitter

View all Seagate ST9900805SS manuals

Add to My Manuals
Save this manual to your list of manuals

Page 69 highlights

The leading and trailing edge slopes of figure 15 shall be preserved. As a result the amplitude value of Z1 is less than that given in table 28 and Z1TOL and Z1OP shall be defined from those slopes by the following equa- tion: Z1TOL = Z1OP x -X----2---O----P 0---,----5---)---x---a---d---d----i-t--i-o---n----a---l---s---i-n----u---s---o---i--d---a---l---j--i-t--t-e----r--)---------X-----1---O----PX2OP - X1OP where: Z1TOL is the value for Z1 to be used for the tolerance masks; and Z1OP, X1OP, and X2OP are the values in table 28 for Z1, X1, and X2. The X1 points in the receive tolerance masks are greater than the X1 points in the receive masks, due to the addition of sinusoidal jitter. Figure 17 defines the sinusoidal jitter mask. Peak-topeak sinusoidal jitter (in UI) 1.5 Sinusoidal jitter frequency (log/log plot) FNOM = 1.5 x 10 9 for 1.5 Gbps FNOM = 3.0 x 10 9 for 3.0 Gbps 1.0 0.1 0 FNOM / 25,000 FNOM / 1,667 Frequency (in kHz) Figure 17. Sinusoidal jitter mask Savvio 10K.2 SAS Product Manual, Rev. D 63

Section	Page
1.0 Scope	7
2.0 Applicable standards and reference documentation	9
2.1 Standards	9
2.1.1 Electromagnetic compatibility	9
2.1.1.1 Electromagnetic susceptibility	9
2.1.2 Electromagnetic compliance	10
2.1.3 European Union Restriction of Hazardous Substances (RoHS)	11
2.2 Reference documents	11
3.0 General description	13
3.1 Standard features	14
3.2 Media description	14
3.3 Performance	14
3.4 Reliability	15
3.5 Formatted capacities	15
3.6 Programmable drive capacity	15
3.7 Factory-installed accessories	15
3.8 Factory-installed options	16
4.0 Performance characteristics	17
4.1 Internal drive characteristics	17
4.2 Seek performance characteristics	17
4.2.1 Access time	17
4.2.2 Format command execution time for 512-byte sectors (minutes)	18
4.2.3 General performance characteristics	18
4.3 Start/stop time	19
4.4 Prefetch/multi-segmented cache control	19
4.5 Cache operation	19
4.5.1 Caching write data	20
4.5.2 Prefetch operation	20
5.0 Reliability specifications	23
5.1 Error rates	23
5.1.1 Recoverable Errors	23
5.1.2 Unrecoverable Errors	23
5.1.3 Seek errors	24
5.1.4 Interface errors	24
5.2 Reliability and service	24
5.2.1 Annualized Failure Rate (AFR) and Mean Time Between Failure (MTBF)	24
5.2.2 Preventive maintenance	24
5.2.3 Hot plugging the drive	24
5.2.4 S.M.A.R.T.	25
5.2.5 Thermal monitor	26
5.2.6 Drive Self Test (DST)	27
5.2.6.1 DST failure definition	27
5.2.6.2 Implementation	27
5.2.6.2.1 State of the drive prior to testing	28
5.2.6.2.2 Invoking DST	28
5.2.6.2.3 Short and extended tests	28
5.2.6.2.4 Log page entries	29
5.2.6.2.5 Abort	29
5.2.7 Product warranty	29
6.0 Physical/electrical specifications	31
6.1 AC power requirements	31
6.2 DC power requirements	31
6.2.1 Conducted noise immunity	33
6.2.2 Power sequencing	33
6.2.3 Current profiles	33
6.3 Power dissipation	35
6.4 Environmental limits	36
6.4.1 Temperature	36
6.4.2 Relative humidity	37
6.4.3 Effective altitude (sea level)	37
6.4.4 Shock and vibration	37
6.4.4.1 Shock	37
6.4.4.2 Vibration	39
6.4.5 Air cleanliness	39
6.4.6 Corrosive environment	39
6.4.7 Acoustics	40
6.4.8 Electromagnetic susceptibility	40
6.5 Mechanical specifications	41
7.0 Defect and error management	43
7.1 Drive internal defects/errors	43
7.2 Drive error recovery procedures	43
7.3 SAS system errors	45
7.4 Background Media Scan	45
7.5 Media Pre-Scan	46
7.6 Deferred Auto-Reallocation	46
7.7 Idle Read After Write	46
8.0 Installation	47
8.1 Drive orientation	47
8.2 Cooling	48
8.3 Drive mounting	49
8.4 Grounding	49
9.0 Interface requirements	51
9.1 SAS features	51
9.1.1 task management functions	51
9.1.2 task management responses	51
9.2 Dual port support	52
9.3 SCSI commands supported	53
9.3.1 Inquiry data	57
9.3.2 Mode Sense data	57
9.4 Miscellaneous operating features and conditions	61
9.4.1 SAS physical interface	62
9.4.2 Physical characteristics	65
9.4.3 Connector requirements	65
9.4.4 Electrical description	65
9.4.5 Pin descriptions	65
9.4.6 SAS transmitters and receivers	66
9.4.7 Power	66
9.5 Signal characteristics	66
9.5.1 Ready LED Out	66
9.5.2 Differential signals	67
9.5.2.1 Eye masks	67
9.5.2.1.1 Eye masks overview	67
9.5.2.1.2 Receive eye mask	68
9.5.2.1.3 Jitter tolerance masks	68
9.5.2.2 Transmitter signal characteristics	70
9.5.2.3 Receiver signal characteristics	71
9.5.2.3.1 Jitter	71
9.5.2.3.2 Receiver jitter tolerance	72
9.5.2.3.3 Compliant jitter test pattern (CJTPAT)	72
9.5.2.3.4 Impedance specifications	72
9.5.2.4 Electrical TxRx connections	73
9.5.2.4.1 Transmitter characteristics	73
9.5.2.5 Receiver characteristics	76
10.0 Seagate Technology support services	77
Numerics	79
A	79
B	79
C	79
D	79
E	79
F	80
G	80
H	80
I	80
J	80
L	80
M	80
N	81
O	81
P	81
Q	81
R	81
S	81
T	82
U	82
V	82
W	82